Advanced Network Devices Sip Zone Line-Out Controller

Advanced Network Devices Sip Zone Line-out Controller

Product Code: eq161162
Availability: In Stock

$1,512.00 $2,116.80

Qty

15 reviews Write a review

Description
Reviews (15)

Connect non-network devices to your network with the Advanced Network Devices SIP Zone Line-Out Controllerby Advanced Network Devices. This controller interacts directly with your facility's mass notification system thanks to its peripheral support and acts as a hub for a variety of devices. The unit supports SIP and is enabled to receive InformaCast Broadcasts.

Peripheral Integration Supports SIP InformaCast Enabled

General
Compatibility	Not Specified by Manufacturer
Inputs / Outputs
Audio I/O	1x RCA Line Output (Unbalanced line level)
Supported Protocols	SIP IPv4 IPv6 802.1X HTTP SLP TFTP NTP SNMPV1 SNMPV2c DHCP IGMP ICMP TCP/IP LLDP-MED UDP MDNS MDNS-SD
Ethernet	10/100 Mb/s
Audio Output	8 / 16 W
Speaker	8 Ohm
Power
Power Source	PoE
Power Input	PoE (IEEE802.3af) 15.4 W or PoE+ (IEEE802.3at) 30 W
Physical
Mounting	4x Unthreaded Holes
Certifications	ISO
Operating Conditions	34 to 122°F / 1 to 50°C at 0 to 95% Humidity
Cable Length	Not Specified by Manufacturer
Dimensions	8 x 6 x 1.25" / 20.3 x 15.2 x 3.17 cm
Weight	1 lb / 0.5 kg

Related Questions and Answers

Q: 1. How can the comms port be setup and used from switcher side to camera operator side?

A: To utilize the comms port on the BirdDog Flex 4K HDMI In to Full NDI Encoder, communication software would be needed. You can find a compatible software here: https://bhpho.to/3YnzJQL.

Q: 2. Can I view the feed from this through the NDI Monitor App on Apple TV?

A: Yes, you would need the NDI Monitor TV app for your apple tv.

Q: 3. Is the L-series plate removable?

A: Unfortunately, the L series plate is not removeable.

Q: 4. I want to stream music via wifi vs. BT in my office; How does this unit connect to your wifi network?

A: The Pyle Pro PTA62BT 6-Zone Stereo Receiver with Bluetooth BH #PYPTA62BT is not a networked AV receiver and will not connect to WI-Fi. It will connect via Bluetooth with your mobile devices to stream music.

Q: 5. I would like to hook up 12 outdoor speakers to this unit and a basic sub. What are the maximum watt speakers can I use? Can you suggest a couple of speakers that would be suitable.

A: The max wattage is 750watts. As long as you dont exceed that rating any 4-8ohm speaker should work fine.

Q: 6. Will the Rs-232 port control a TV on/off?

A: The BirdDog Flex 4K Out Full NDI Decoder - BH #BIBDFLEXDEC will not control power on/off of a television via its RS232C port.

Q: 7. do you need an external amp with the PCM 2000 system ?

A: Yes, you still need an external amp with this system. The PCM 2000 in no way amplifies, only splits paging up into zones.

Q: 8. is the Remote for this device Infrared ?

A: The Pyle Pro PTA62BT 6-Zone Stereo Receiver with Bluetooth BH #PYPTA62BT does have an infrared remote.

Q: 9. Can I use this as an NDI Source in OBS or Xsplit Broadcaster? Do I need the transmitter to be on the same network as the receiving device?

A: Yes, an NDI workflow is compatiable with X-Split and OBS. The transmitter does need to be on the same network, it's integral to how NDI functions. Evey component of this workflow has to be NDI compatiable.Newtek has plugins and software available to make your computer, OBS, and Xsplit Broadcaster NDI compatible on their website.

Q: 10. how do you connect multiple speakers via bluetooth?

A: The Pyle Pro PTA62BT does not connect to bluetooth speakers. It pairs as a bluetooth output device to bluetooth input devices like smartphones and tablets. It has an amplifier inside of it that is made for powering speakers via speaker wire through the back of the receiver.

Joe	08/09/2024
[8 Ohm] Perfect for my multizone install. Works as intended and has all the right features! 5

Fred F	08/09/2024
[10/100 Mb/s] The line I connected to was expected to be 70V but may not have been. I adjusted the potentiometer close to 20V and it is working fine. 5

Joel	06/09/2024
[10/100 Mb/s] This interface resolved some issues with using a TOA amp pre-out to feed our FM transmitter. Five minutes to install it, problem gone. 5

Derrick	21/07/2024
[8 / 16 W] We used this to clear up awful feedback on a P/A system. We put this in-line with our system and the feedback is completely gone. So, for my application it was perfect. 5

CinematicFilm	07/07/2024
[10/100 Mb/s] The cable sets down the gain from a mic or mixer to a DSLR 3.5mm audio input. Finally the audio in the captured file is useful without having to use double system sounds files and resyncing in post. 5

anyonymous	04/07/2024
[8 / 16 W] This is a very reliable phone-to-PA interface. It is very simple to install and reasonably priced. Since wrong numbers are a problem with some of my systems, requiring an access code is essential. It is very easy to program. 5

Michael	02/07/2024
[8 Ohm] I used this cable to take the audio from my Tascam record and sent it to my DSLR. Worked Great; gave me greater control of the audio going into my DSLR. 5

anyonymous	24/06/2024
[PoE] We use this in an 1100 seat venue as our media feed. The Pressmite does everything it should: provides clean signal to whatever is plugged into it. We have been using one for about five years now and no one has ever complained. 5

Roy	29/05/2024
[8 Ohm] With the FCC about to shut down the thousands of dollars worth of UHF professional mics I have, I took a chance on the new Sony Bluetooth offerings from B&H. After finding NO interference in either midtown Manhattan or downtown Washington, DC, I wanted some spare attenuated cables to use from my four Sony Bluetooth mic receivers to (a splitter to) my camera. Since Sony doesn't sell parts direct, I tried this from a trusted supplier (B&H), and it works great. Don't need to replace the Sony OEM cable in early going, but nice to have this back-up in my kit! 5

Daniel	27/05/2024
[PoE] Having a Active model like this Whirlwind PressMite takes the guess work out of it as this one takes Mic or Line in & is adjustable .... I'm glad I didn't go cheap on this ! 5