The 5-year Verkada Viewing Station License - 5 Yearsauthorizes the use of the Verkada Viewing Station for monitoring video feeds from your surveillance network. This license is required to use the station.

For Use with Verkada Viewing Station    Required to Use Verkada Viewing Station

Related Questions and Answers

Q: 1. Can u update Samyang lens firmware without buying special hardware?

A: They have instruction on their website as to how to update the firmware.

Q: 2. Is the "INST. IN" in on the Rolls PM351 a 1/4" TRS input that can accept a line-level stereo signal?

A: Yes. The instrument input on the Rolls PM351 Personal Monitor Station uses a 1/4" TRS connector that can accept instruments and line level signal. The line input also uses a 1/4" TRS connector that will accept line level. Both can be used for stereo signal by setting the corresponding mono/stereo switch for stereo input signal.

Q: 3. If connected to a Mac Studio, and loaded with Pro Blade memory sticks, will this unit auto power down at some point? And if so, what's the trigger? I'd need this to sty powered up.

A: The SanDisk Professional PRO-BLADE STATION has its own power adapter; it'll remain powered as long as it's connected to its power adapter, though it will turn off on its own after a few minutes of inactivity if it's not plugged into a host computer.

Q: 4. So what is this? Do the multiple 4 TB drives allow me to create a RAID array to backup my work? Or is this purely a nifty external SSD disk? I don't understand what's so special about it.

A: The SanDisk Professional PRO-BLADE STATION is a docking station for the SSD PRO-BLADE mags.

Q: 5. Does the dock come with it’s own power supply, and a lightning 4 cable?

A: Yes, this SanDisk Professional PRO-BLADE STATION comes with a Thunderbolt 4 cable and it’s own power supply.

Q: 6. How loud is the fan noise in dBA? Will this unit work in a quiet studio, fully loaded 16TB?

A: SanDisk has not provided a spec for the operational noise level of the PRO-BLADE STATION's internal fan, but as this is a solid state storage device the noise level will be much lower than that of a traditional hard drive enclosure.

Q: 7. If I were to use this in line with the MX41 as an input to increase inputs to the monitor, would the signal from the mx41b come through ?

A: To begin with, I'm confused with your question, as you refer to an MX41, and an mx41b. Presuming that you mean the Rolls MX41B in both instances, then I am further confused by your question about whether the signal from it would come through. The more clearly you state your question, the better the rest of us can understand and offer help.That being said, there should be no problem to take the output from the MX41B into either the line input or instrument input of the Rolls PM351 and hear all the inputs from both units mixed together on the output of the PM351. It has lots of range and volume available, and is a great, clean headphone amp/mixer/direct box. You will want to pay attention to your stereo and mono cables, as well as the stereo/mono jumpers on the PM351, so you know what you are actually listening to. The MX41B is stereo, so I don't know what happens when you put a mono cable into it... it may only appear on one side of the output. Stereo/mono on the PM351 is selectable with two jumpers. Careful with those jumpers, though, they are black and small and easily lost.The quarter-inches are all unbalanced, too, so don't run those cables more than about 10 feet if you can help it. The XLR's are fine for any length, of course.Hope that helps.rcarbaugh

Q: 8. Does Sandisk Pro Blade Transport work with Canon 5D Mark IV?

A: The SanDisk Professional PRO-BLADE STATION is just the enclosure without any drives. The SanDisk Professional PRO-BLADE TRANSPORT drives will not work directly with the Canon EOS 5D Mark IV DSLR Camera, as the Canon camera cannot record directly to a drive.

Q: 9. It looks like it clips onto table, in one photo. In another photo, it looks like it has a base and sits on surface. Which is it?

A: The Ilford ILFOLUX Color Viewing Lamp comes with both the base and desk clamp.

Q: 10. Any tips on adjusting the focus point? After updating lens firmware it was at +1. No where does it explain what the + and - settings will achieve.

A: The lens will need visual calibration. This will be the 2nd step and you will need a lens calibration board to set up normal parameters on your lens. Please review the following tool to calibrate your lens. Vello LENS-2020 Lens Calibration Tool BH #VELENS2020 • MFR #LENS-2020 https://www.bhphotovideo.com/c/product/1439588-REG/vello_lens_2020_af_lens_calibration_tool.html?sts=pi&pim=Y