The SKB iSeries Sony Camera Case with Wheelsis made of high-strength polypropylene copolymer resin and has a custom cut polyethylene foam interior for the Sony FDR-AX1, PXW-Z100, HDR-FX1000, HVR-Z5U, HDR-AX2000, HXR-NX5U, or HXR-NX3. There are also additional pre-cut sections for batteries, memory cards and a large accessory pocket that can fit an additional shotgun microphone or other accessories. Convenient wheels and a pull handle provide easy transport.

The case is resistant to corrosion and impact damage and features molded-in hinges and a snap-down molded handle with rubber grip. It has trigger release latches for quick but secure access. A complete gasket seal makes the cases watertight and submersible and an automatic value provides quick equalization when there are changes in atmospheric pressure. Loops are provided for adding an optional padlock to provide extra security.

Fits FDR-AX1, PXW-Z100, & Select Cameras    High-Strength Resin Exterior    Custom Cut Foam Interior    Room for Camera Body and Accessories    Resistant to Corrosion and Impact Damage    Watertight and Submersible Case    Automatic Pressure Release Valve    Trigger Release Latches    Snap-Down Handle with Rubber Grip    Convenient Wheels and Pull Handle

• Custom cut PE foam to fit Sony FDR-AX1, PXW-Z100, HDR-FX1000, HVR-Z5U, HDR-AX2000, HXR-NX5U, or HXR-NX3 video cameras
• Compartments for batteries, memory cards and shotgun microphone, and accessories
• Ultra high-strength polypropylene copolymer resin
• UV, solvent, corrosion, and fungus resistant (MIL-STD-810F)
• Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)
• Automatic ambient pressure equalization valve (MIL-STD-648C & IP67)
• Resistant to corrosion and impact damage
• Molded-in hinges
• Rubber over-molded cushion grip handle
• Locking loops for a customer supplied lock
• Patented "trigger release" latch system
• Convenient wheels and pull handle

Related Questions and Answers

Q: 1. will this bat case fit 10 softball bats?

A: Yes.

Q: 2. Do the Rokinon Xeen fit?

A: Xeen's fit, but not well. The 16mm is a good fit, but the other lenses are taller than the holes, so about an inch of the lens hangs out. The case can still close, but it's tight. I bought this case specifically for my Xeen's and will be returning it because it's not a correct fit.

Q: 3. How is the bottom foam layered? 2"+2"+2" 1"+2.5"+2.5"......etc

A: The foam in the SKB iSeries 4719-8 Waterproof Utility Case with Wheels (Black, Layered Foam) is, FOAM IN LID; 2" over 1" convolute BASE FOAM LAYERS (Top to Bottom); 2" solid (x2), 1 1/2" solid (x1), 1/2" solid.

Q: 4. Does this bat case fit 10 softball bats?

A: Hello Melissa Yes, the case will fit 10 Softball or Baseball bats.

Q: 5. Anyone use this case with the Rokinon Cine DS Lenses? Especially the 135mm?

A: I have the Rokinon Cine DS lenses up thru 85mm and they fit great in this case. I also have the Canon 24-70 which measures almost 5.5 inches long with the caps on, and it fits fine, too. I would not go much longer than that. You might get away with 6 to 6.5 inches long but it would be tight.

Q: 6. Will these spaces fit Cooke Panchri i/Classic prime lenses?

A: Most of the lenses will fit but a few of them are too long/tall. (for instance the 65mm Macro).

Q: 7. How dense and durable is the foam insert for the SKB 3I-20118LENS case? Will it holds its shape over time?

A: Hi David, Thank you for your interest in our cases. The foam uses a fine-cell formulation and is dense. The specific type of foam used in the base of the case is called Synergy 1000. It will hold up for 20 years or longer. It will hold it's shape over time without issue unless you put an item in with a lot of pressure in the pocket and then it will open up the pocket a little. You're welcome to contact our customer service department if you would like a technical sheet on the foam breakdown.Thank you,Will

Q: 8. Is SKB layered foam PE Foam (Polyethylene) or Ester Foam (Polyurethane)?

A: The SKB iSeries 4719-8 Waterproof Utility Case with Wheels (Black, Layered Foam) has open cell Ether-Like-Ester (E.L.E) foam.

Q: 9. last question: Do the Rokinon's travel from side to side in the cutouts? I noticed the holes are 125mm and all the Rokinons are 90-100mm in diameter.

A: If the lenses are smaller than 125mm, then yes they will move back an forth in the holes. I would say that damage would be unlikely. However, I would suggest for peace of mind getting an empty case and filling it with foam and doing your own cut outs.

Q: 10. is there foam on the top??

A: This is an empty case, there is no foam in the case or on the top of the case.