Achieve motorized suction with ease using this 4.5" Tilta Hydra Suction Cup 4.5" for Camera Mountingfrom Tilta Hydra Suction Cup 4.5" for Camera Mountingfor dynamic vehicle-mounted shots. The suction cup is equipped with a high-performance motor that secures to your surface of choice in just five seconds. Air pressure detection occurs in real time and is displayed on the integrated LCD while additional air is automatically pumped in.

The suction cup can support vertical loads up to 44.1 lb, easily accommodating your gimbal or cine rig. A 2000mAh battery keeps the suction cup running for up to eight hours and recharges via a USB-C port with PD support. Separately available modular top mounts can be secured to the suction cup for different rig configurations.

44.1 lb Vertical Load Capacity    High-Performance Motor    Air Pressure Detection    LCD Screen for Monitoring    Modular Top Mount Options    2000mAh Battery, USB-C Charging Port

Related Questions and Answers

Q: 1. does the design of this rig make it difficult to mount the gimbal low to the ground? for example: with 1 cup connected low to the bumper and 2 cups connected to the flat/gently-curved part of the trunk/hood, it looks to me like the diagonally-mounted support strut might be easily blocked by the edge of the hood/trunk when trying to connect it from the vertical to the horizontal piece ~ does this make sense? thoughts?

A: There are a number of different ways to mount this support depending on the accessories that you would like to purchase with it and where you want to position it on the car. for example to get low angle shots it seems imperative that you purchase some single handed gimbal ( like the Ronin RS2). On the sides of the car it would be quite easy to get a low angle shot when mounted to the car door on the front or back of the car it seems as though it would be quite difficult. The design of the car will also affect how easy/difficult it is to get the shots that you want. for example in the photos they used a BMW Sedan which poses a challenge when mounting this rig to the rear but if they were to swap that car for an SUV, or mini van then there would be a lot more surface area on the back of the car making it feasible to get a low angle shot from the back.

Q: 2. Could this be mounted to a helicopter??

A: Yes, you should be able to mount the Tilta Hydra Alien Car Mounting System (V-Mount) to a helicopter, but I don't know how well it would stay on as road conditions are different than air conditions, and this mount is intended for use on the road.

Q: 3. Can it use the RS4 Pro Rs4 ?

A: Yes, the Tilta Hydra Alien Car Mounting System (V-Mount) will also support the DJI RS4 and RS4 Pro gimbals.

Q: 4. will this work with the ronin-m? or ronin 2?

A: No it will not this is designed for the New Ronin RS 2 and is part of the Tilta DJI Ecosystem for the new DJi gimbals

Q: 5. Will this work for a Ronin S?

A: No, this is only compatible with the DJI RS2 and RSC2 gimbals. It comes with the Power Baseplate for DJI RS2 and RSC2 gimbals.

Q: 6. Is there a 2" receiver hitch mount option for this to use with or instead of the suction cups?

A: Unfortunately no, the Tilta Hydra only has battery mount configuration options.

Q: 7. Bag?

A: Yes, a Waterproof Hard-Shell Safety Case is included.

Q: 8. How long is the arm?

A: The arm is 258mm long.

Q: 9. Does this work with the DJI RS3 Pro?

A: Yes, the Tilta Hydra Alien Car Mounting System is compatible with the DJI RS3 Pro,.

Q: 10. Ronin MX on tilts Hydra Alien arm? The weight limits are there but can I mount a Ronin plate where the power adapter mount goes for use with older ronins?

A: One can consider the CineMilled Universal Mount for DJI Ronin-M/MX Gimbals BH #CICM003 to mount above the Ronin S power supply baseplate provided with the Tilta Hydra Alien Car Mounting System (V-Mount). See link below. https://bhpho.to/3pu1ipE