Capture smooth, dynamic action shots from the interior or exterior of a vehicle with the Tilta Hydra Articulating Car Mount Systemfrom Tilta. The system includes three 6" suction cups with NATO rail mounts, three heavy-duty articulating arms, and a 75mm ball head that can be adjusted up to 15° to achieve your desired shooting angle. A Manfrotto quick release system allows you to secure your compatible Arca-type or Manfrotto camera cages and rigs to the car mount. The system also includes a 75/100mm bowl adapter to accommodate different ball heads. Once assembled, the system has a load capacity of 44 lb to support most rig configurations. Store all of the components in the included carrying case for easy transport.

Stable Car Mount System for Camera Rig    Three 6" Suction Cups with NATO Rails    75mm Ball Head, Manfrotto Quick Release    Heavy-Duty Articulating Arms    44 lb Load Capacity

Related Questions and Answers

Q: 1. Will this work with the DJI Ronin m?

A: Yes, you will need to use an adapter for the Ronin M.

Q: 2. This car mount work with zhiyun crane 3s?

A: Unfortunately, the Hydra Alien Car Mount has a Power Supply Baseplate that is only compatible with the DJI RS 2.

Q: 3. Does this work with the DJI RS3 Pro?

A: Yes, the Tilta Hydra Alien Car Mounting System is compatible with the DJI RS3 Pro,.

Q: 4. Where can you get replacement plates for the mount? Can't find them.

A: You will have to get replacement plates for the Tilta Hydra Alien Car Mounting System (V-Mount) directly through Tilta.

Q: 5. What kind of adapter is needed for this to work with the DJI Ronin m?

A: The Tilta Hydra Alien Car Mounting System (V-Mount) is compatible with any gimbal that can mount via 1/4″-20 screws and power via P-Tap.

Q: 6. What are the best stiffness settings for using it with an A7SIII with a lighter lens?

A: The Tilta Hydra Alien Car Mounting System (V-Mount) does have settings for payload weight. It is up to the you to set the weight of the payload by adjusting the pressure of the arm, Tilta does not have pre-set stiffness settings on the arm, unfortunately. I would recommend generally using a bit heavier setup to achieve a more stable image.

Q: 7. does the design of this rig make it difficult to mount the gimbal low to the ground? for example: with 1 cup connected low to the bumper and 2 cups connected to the flat/gently-curved part of the trunk/hood, it looks to me like the diagonally-mounted support strut might be easily blocked by the edge of the hood/trunk when trying to connect it from the vertical to the horizontal piece ~ does this make sense? thoughts?

A: There are a number of different ways to mount this support depending on the accessories that you would like to purchase with it and where you want to position it on the car. for example to get low angle shots it seems imperative that you purchase some single handed gimbal ( like the Ronin RS2). On the sides of the car it would be quite easy to get a low angle shot when mounted to the car door on the front or back of the car it seems as though it would be quite difficult. The design of the car will also affect how easy/difficult it is to get the shots that you want. for example in the photos they used a BMW Sedan which poses a challenge when mounting this rig to the rear but if they were to swap that car for an SUV, or mini van then there would be a lot more surface area on the back of the car making it feasible to get a low angle shot from the back.

Q: 8. Is a gimbal required

A: The Tilta Hydra Alien Car Mounting System (V-Mount) is just a mounting solution. It does not include a gimbal with the kit. This system is compatible with the DJI RS2, RS3, RS3 Pro, RS4 Pro, Crane 3S, Ronin 4D and any other gimbal that can mount via 1/4″-20 screws and power via D-Tap or internally.

Q: 9. Ronin MX on tilts Hydra Alien arm? The weight limits are there but can I mount a Ronin plate where the power adapter mount goes for use with older ronins?

A: One can consider the CineMilled Universal Mount for DJI Ronin-M/MX Gimbals BH #CICM003 to mount above the Ronin S power supply baseplate provided with the Tilta Hydra Alien Car Mounting System (V-Mount). See link below. https://bhpho.to/3pu1ipE

Q: 10. Will this work for a Ronin S?

A: No, this is only compatible with the DJI RS2 and RSC2 gimbals. It comes with the Power Baseplate for DJI RS2 and RSC2 gimbals.