The Polymaker 2.85mm PolyDissolve S1 Filament 750g Naturalis a PVA-based water dissolvable support for PLA, TPU, PVB, and nylon based filaments. It was specifically engineered to have an optimal interface with these materials while also displaying good solubility.

It can take between 6 to 12 hours to fully dissolve depending on your setup. You can speed up the process by increasing the water temperature, changing the water regularly, and adding a pump to make the water flow.

2.85mm Filament Diameter    750g Weight    PVA-Based Material    Water Dissolvable Support

• Printing Temperature: 419 - 437°F / 215 - 225°C
• Bed Temperature: 77 - 140°F / 25 - 60°C
• Printing Speed: 30 - 40 mm/s
• Fan: ON

Direct Drive

• Retraction Distance: 1 mm
• Retraction Speed: 20 mm/s

Indirect Drive

• Retraction Distance: 3 mm
• Retraction Speed: 40 mm/s

• 176°F / 80°C for 12 hours (Only if the material has absorbed moisture)
• PolyDissolve S1 is very hygroscopic, please make sure to use a dry box

Related Questions and Answers

Q: 1. What size are the 4 image sensors?

A: The size of the sensors are not listed, only that is has Sony EXMOR™ CMOS Image Sensors.

Q: 2. How is the connection between the camera and the Gimbal? what kind of cable ? to make a video transmission transmission

A: The Sony Gremsy Gimbal T3 for Airpeak S1 Drone will connect to Sony cameras via USB-C cable or Micro USB cable.

Q: 3. Will this fit a celestron powerseeker 127eq?

A: No, unfortunately, the MrStarGuy Natural Light Adjustable Solar Filter (165-195mm OD) will not fit the Celestron PowerSeeker 127EQ Reflector Telescope, which has a front aperture of 127mm. The MrStarGuy Natural Light Adjustable Solar Filter (125-155mm OD), B&H # STSGFT043Y • MFR # SGFT043Y, or the MrStarGuy Natural Light Adjustable Solar Filter (105-135mm OD), B&H # STSGFT042Y • MFR # SGFT042Y, are better options.

Q: 4. can you use this paper 8.5x11 with the Epson XP-960 and do you load it with printable side up in the large cassette tray?

A: I seriously doubt that you can feed this paper through a cassette. I have an Epson P800, into which this paper must be feed by hand using the front fine art loader. It will not run through the top loading feeder on the P800. This paper is not listed in the Manual for this machine. You may able to tell if the machine can handle it by seeing if you can select it in the Printer Dialog Box under Printer Settings--Media Type--Fine Art Paper--Hot Press Natural. If there is no setting for this paper, then you are probably out of luck. Last resort, call Epson. I'd be sure your machine can handle it, before chewing up this expensive product and ruining your machine.

Q: 5. Does this just produce a flat photo or can it produce a scaled 3D model?

A: It supports equirectangular still image by simply take one frame out of the video. It does not produce a scaled 3D model though.

Q: 6. What's the operating temperature range and is it weather proof?

A: The Z CAM S1 6K Professional VR Camera temperature range is 0-40°C and is not weather proof.

Q: 7. How does one mount this to a tripod or leveling base?

A: This camera has a standardf 1/4 -20 female bushing on its bottom. There is a decent YouTube video showing how to mount and counterblance this camera at How to balance the Insta360 Pro, Obsidian, Z Cam S1 and more on the Moza Guru 360 Air gimbal .

Q: 8. Should the filter rest against the camera lens or should there be a slight space so the lens does not actually touch the filter?

A: It is recommended to leave a slight gap between the lens and the MrStarGuy Natural Light Adjustable Solar Filter in order to reduce the risk of scratching the filter.

Q: 9. Can you walkBout with?

A: Itis battery operated,so sure. Tripod mounting would yield more pleasing results.

Q: 10. There is an iPad zCam Contoller app, what additional equipment is needed to control the camera with the App via wifi?

A: There is no additional equipment needed to used the controller app with the Z CAM.