Designed for protection, organization, and rapid deployment, the DJI Matrice 300/350 Hard-Shell Case | Go Professionalfrom DJI Matrice 300/350 Hard-Shell Case | Go Professionalfeatures an impact and weather-resistant hard-shell exterior, and a water- and dust-resistant interior closed cell foam insert. The insert has been precision cut via water jet to provide a plethora of storage compartments for your M300 or M350 drone with landing gear and accompanying accessories. In addition to the sections on the main insert, there is a payload tray and additional storage cavities underneath. Traveling with all of this equipment is safe and easy, with a trigger release latch system, telescoping handle, and in-line skate-style wheels.

For DJI Matrice 300 or 350 Drone    Holds a Payload, 2 Controllers & More    Water & Dust Resistant    Resistant to Impacts, UV & More    Water-Jet Precision-Cut Compartments    Telescoping Handle & Built-In Wheels    Trigger Release Latch System    Snap-Down Cushion Grip Handle    Ambient Pressure Equalization Valve    Padlock Holes with Stainless Steel Clips

• DJI Matrice 300 or 350 drone with batteries attached
• Two DJI Smart Controller Enterprise or DJI RC Plus controllers
• Three spare battery sets (One under the payload tray)
• H20, H20T, Z15 Spotlight, Z30, or FLIR XT2 payload
• Landing gear
• Two controller batteries
• Spare propellers
• Miscellaneous accessories

  • Resistant to impact, UV, solvents, corrosion, and fungus
  • Ambient pressure equalization valve
  • Snap-down rubber over-molded cushion grip handle
  • Molded-in hinge for added protection
  • Padlock holes with stainless steel protector clips

    Related Questions and Answers

    Q: 1. Wanted to know if there was a stabilizer type vest or anything that would work with this to help reduce stress and fatigue while using Ronin-S? Thank you

    A: Try the glidegear dna 6000 stead I am or easyrig

    Q: 2. Does this fit A7iv?

    A: We tested the GoScope Alpha Hard-shell Go Case and it does not fit the Sony A7IV.

    Q: 3. Is the ronin-S will be able to fit in the Sony a6300??

    A: Yes. That camera also has start-stop/shutter control using the included cables.

    Q: 4. Will this case fit Sony a7R IV with an RRS L-bracket?

    A: Yes, you would be able to fit the A7R IV with the RRS L bracket in this case.

    Q: 5. Will this case fit a P3P with a gimbal guard attached between the landing gears?

    A: Anything that will fit within the inside parameters of the landing gear (LxHxW) should fit in the case.

    Q: 6. Can I power Sony a6500 with Ronin S?

    A: The Ronin S has two 12v/2A four pin outlets built in to the base plate shoe. You can power anything that takes that kind of power and has an adapter cable.

    Q: 7. Can we calibrate the turn ratio of the follow-focus?

    A: Currently this feature is only available on the external focus motor. We'll be adding more and more features and capabilities to Ronin-S so it's likely this feature will be added.

    Q: 8. Will this fit Sony 7Riv with 12-24 f2.8?

    A: The Sony a7R IVA Mirrorless Camera with the Sony FE 12-24mm f/2.8 GM Lens is too large to fit in the GoScope Alpha Hard-Shell Go Case for Sony a7 II, a7 III, a7S II, a7R II, a7R III with 24-70mm f/2.8 Lens (Black).

    Q: 9. Would this fit an a7iii with the Sony FE24-240 f/3.5-6.3 OSS Lens?

    A: Yes. The Sony 24-70mm 2.8 lens measures 5.37" long. The Sony 24-240mm is 4.67" long. So there will be more than enough room.

    Q: 10. Has anybody tried this one with a BMCC 2.5K/4K, Does it fit?

    A: The 2.5K size and weight don't seem like they would be an issue The Pocket Cinema 4K may be too wide, modifications for balance may be necessary, though we have not tested this specific setup so we can't say for certain. More testing is necessary.