Recommended for engineers seeking a punchy preamp with plenty of warmth on low frequencies, the RE-VR Cartridge from GC Audio is a preamp module designed exclusively for the Inherit Modular Preamp System. Designed as a reissue of the preamp in a famous British mixing console from the '80s, the RE-VR cartridge features plenty of improvements for the best possible results in modern recording scenarios.

When loaded into an Inherit chassis, the RE-VR provides a -20 dB attenuation pad for reining in overly hot signals. The combination of a low-noise op-amp and a fully rebuilt TF10015 transformer with identical specs to the original provides exceptionally low distortion. Finally, the PCB features a carefully selected routing path for the most efficient signaling possible with this design.

Balanced Solid-State Preamp Module    Designed for Inherit Hot Swap System    Based on Famous '80s British Mixer    Rebuilt TF10015 Transformer    Punchy and Warm Sound Character    Low-Noise Op-Amp    -20 dB Attenuation Pad    20 to 70 dB Stepped Gain Control    Carefully Routed PCB Design

A welcome feature of the RE-VR cartridge for pro engineers is stepped gain control, which is provided in 12 steps:

• 1 = 20 dB
• 2 = 24 dB
• 3 = 28 dB
• 4 = 32 dB
• 5 = 36 dB
• 6 = 40 dB
• 7 = 44 dB
• 8 = 48 dB
• 9 = 54 dB
• 10 = 60 dB
• 11 = 66 dB
• 12 = 70 dB

Related Questions and Answers

Q: 1. how do I install my PP999 as it came with no instructions?

A: Connect your turntable to the PP999 inputs and connect the PP999 outputs to a line level input on your receiver or amplifier.

Q: 2. does this unit (PP444)come with power transfer for $13.78?

A: Yes

Q: 3. Can I plug this camcorder into my PC with the USB port and download videos?

A: I think you can I usually just take the card out and put it in the card reader on my computer great little camera

Q: 4. Do this devise will work with Sanken COS-11D XLR conector wired.To connect to Sennheiser G3 wireless system?.I will like to use my wired Sanken for wireless too, do this is possible?

A: This device has the special female mic connector (1/8 locking) for Sennheiser lavelier mics that are normally used with the G3 wireless system. It converts only those mics so they may be used with standard XLR mic cables. So this device has a male XLR connector that plugs into a standard mixer mic input. It is not suitable for connecting other kinds of mics with XLR connectors.

Q: 5. I have a TRAM TR-50 lav mic that is made to use with the Senn EW100 G3 system. I have teh Senn ME2 as well that came with the G3 kit. I would like to be able to use both the TR-50 and the ME2 wired to my SD-302. Since the TR-50 is wired to work with the G3 I assume this would work to use it wired (in lieu of the TRAM TR 79+ unit for the same purpose). Can anyone who as ACTUALLY done this confirm that it will work? I too assume it will, but would like to hear from someone who has actually done it if at all possible. Thanks!

A: I know it doesnt work with my Countryman B3. I think it is tuned for the ME2. It clips and distorts with my Countryman. It is possible if the TRAM is similar sensitivity as ME2.

Q: 6. What are the interior and exterior dimensions of the GC-11? PentaxRumors shows pic where GC-9 will just barely fit the GR iii, so I wonder if the GC-11 is thick enough for the Sony RX100 III, which is 4 x 2.37 x 1.63"?

A: the Ricoh GC-11 Soft Case is designed to hold the Ricoh GR III and Ricoh GR IIIx Digital Cameras. The larger GR IIIx which is a tighter fit in the case is 4.3 x 2.4 x 1.4". With the Sony Cyber-shot DSC-RX100 III Digital Camera being a thicker camera at a bit over 1.6" in depth, this case would not be a good fit.

Q: 7. Will this fit the GR II?

A: Yes.

Q: 8. How is this product different than the Rode VXLR+ ? Voltage ? Impedance ?

A: The Rode VXLR Plus does not provide the same voltage that the Sennheiser provides. The Rode does 3-5v. For example: the Sennheiser ME 2 requires 7.5v. The Rode VXLR Plus would not supply that voltage.

Q: 9. Could this device work with the Sanken COS-11D Omni Lavalier Mic(B&H # SAC11WNSETRB MFR # SAN-11DWNBKTRSE)? Thanks Renzo

A: MZA-900P is listed for compatibility with Sennheiser E 908B, E 908D, HSP 2, HSP 4, ME 2, ME 3, ME 4 and MKE 2 EW Gold microphones. We offer this model for the Sanken COS-11D with the 3.5mm connector for Sennheiser transmitters: B&H # AMEMP3.5

Q: 10. Can you mount this in a vehicle and use the vehicles cigarette lighter adapter as a power source?

A: This camera cannot be run off any other power source. Battery only.