Streamline your installation process while also giving your system ample power with the Corsair RM850x SHIFT 80 PLUS Gold Modular Power Supply. Not only does the SHIFT allow you to pick and choose the cables you need for your equipment, but it also places Corsair's Type 5 Gen 1 micro-fit PSU connectors on the side, working alongside your dedicated cable management spaces for a more organized experience.

Offering up to 850W and built off the ATX 12V Version 3.0 standard, you are able to deliver ample power to your gaming-focused components with ease while balancing electrical loads. Modular cable design allows you to pick and choose which cables you need or want to use depending on your system's configuration, giving you more breathing room inside the case while reducing cable clutter. Aside from the standard motherboard and CPU cables, you also get an array of PCIe cables giving you a total of four connectors between two 6+2 connectors on two cables and two 6+2 connectors on a single split cable. For NVIDIA 40 series graphics cards, a single dedicated 12VHPWR cable is included that further reduces cable clutter. You also get 12 SATA connections and eight PATA connectors for storage drives and peripherals, respectively.

850W Total Wattage    ATX 12V Version 3.0    12VHPWR Cable    4 x PCIe Connectors    12 x SATA Connectors    8 x PATA Connectors    Modular Cable Design    Side-Panel Connectors    140mm FDB Cooling Fan    80 PLUS Gold Efficiency

The SHIFT incorporates a unique design that places the traditional PSU-based connectors on the side as opposed to the rear of the unit, giving you a clear view of your connectors and streamlining your installation process when working in cases with side-accessible cable management areas.

The ATX 3.0 standard demands a high level of reliability and power efficiency, meeting the 80 PLUS Gold certification, giving you up to 87% and 90% efficiency at full- and half-loads, respectively.

A low-friction, fluid dynamic bearing 140mm fan with Zero RPM mode support ensures your PSU runs cool while staying virtually silent when not under high load.

Built with 100% Industrial-grade, 105°C-rated Japanese electrolytic capacitors for unwavering power and reliability.

The PSU and cables will fit in any PC case that supports ATX PSU format and is at least 8.3" (210mm) wide. The PSU must also be accessible from the side when mounted in the case.

Related Questions and Answers

Q: 1. Would this work to trigger my Elinchrom Five from a Leica SL-2S?

A: The Impact PowerSync16-80 Transceiver (2-Pack) is not compatible with the Elinchrom FIVE monolight.

Q: 2. Will the transmitter fire from a pc link on older film cameras? Say on a Hasselblad or Rollei TLR, for example?

A: I've used this transmitter with my Hasselblad 500CM and it works fine. The only issue I had was that the very small PC sync cable that came with the transmitter started acting funny and no longer works consistently (I'm assuming there's an issue with the contact in the piece on the end of the cable). But that's a problem with the sync cable, not the transmitter.

Q: 3. Is it work with Sony A7 II + Nissin i40(sony version)?

A: I don't see why not. I haven't had any trouble with it working with any of my sony hotshoes or off brand flashes.

Q: 4. Good day, may I know if this transceiver support HSS and TTL? I also want to believe it should be able to work with old Minolta/Sony flash like the 5600 HS Shoe Mount Xenon Flash (For Minolta) and Sony ILCA-A77M2 while also using the necessary adapters like the TF-323 SONY & Minolta TTL Hot Shoe to PC Sync Adapter.

A: The Impact PowerSync16-80 Transceiver is a fully manual transceiver. It does not have TTL or high Speed Sync capabilities. As the Minolta 5600HS Flash does not have a PC sync terminal, you would need to purchase a hot shoe adapter such as the Vello HSA-CSMSA Multi-Interface to Sony/Minolta Shoe Adapter, B&H # VEHSACSMSA, to connect the Impact PowerSync 16-80 Transceiver to the Minolta 5600HS Flash.

Q: 5. Can I use this transceiver with Elinchrom D-Lite 400W/s RX 4 Flash Head?

A: If you had 2 of these transceivers you could use it with the Elinchrom D-Lite 400W/s RX 4 Flash Head. The Impact PowerSync 16-80 will not fire the internal receiver on the Elinchrom. You need to have 1 PowerSync 16-80 attached to the 3.5mm sync port of the Elinchrome and 1 PowewerSync 16-80 on the camera.

Q: 6. Is device compatible with Sony A7RIII for remote trigger? If so does it require a cable from device to camera?

A: To trigger the A7R III remotely, you would need one of these units connected with the Vello 3.5mm Remote Shutter Release Cable for Select Sony Cameras with Multi-Terminal, BH #VERCCS235, while the second Impact unit is the transmitter in your hand. https://bhpho.to/2GvqNAr

Q: 7. Is there white balance or adjustable color correction?

A: Yes, this webcam has both white balance and adjustable color correction.

Q: 8. is it possible to get a copy of the user manual before purchasing ?

A: Please email info@a href= http://gradusgroup.com target= _blank gradusgroup.com/a for a manual.

Q: 9. Is this compatible with a canon 6d markii?

A: This can be used with the Canon EOS 6D Mark II.

Q: 10. Will this work with an Impact PowerTrigger 16 Channel Receiver (#IMPTAC16R)?

A: I do not think so since the receiver works in the 433 MHz radio signal an d the powersync 16-80 transceiver use a 2.4 GHz signal and 80 coded channels.