The stainless steel RDL DS-J3 Mic/Line Input Assembly with XLR Jacksfrom RDL DS-J3 Mic/Line Input Assembly with XLR Jacksis a complete audio input panel assembly. Its front panel features a female XLR jack and two phono jacks. The XLR is connected directly to the rear panel barrier block and the phono jacks are intended for mono or stereo consumer level sources. LEFT and RIGHT channels are combined and balanced through audio transformers configured to reject induced hum. The line level output is provided on the rear panel terminal block for connection to 10 kΩ or higher input impedance line level module or equipment inputs. The back of the D SERIES-J3 is finished with a metal enclosure clearly labeled for installation.

The D SERIES-J3 fits directly into back boxes, available from RDL to fit cabinets of US or international walls (RDL WB-1U). They may be mounted directly into cabinets or most standard US single gang electrical boxes.

5 x Terminal Block Connections    1 x Female XLR Jack    2 x Phono Jacks for Mono/Stereo Sources    Audio Transformers Reject Induced Hum    Fits Directly in Back Boxes (WB-1U)    Finished with a Metal Enclosure

Wall mounted audio inputs

XLR microphone input with gold contacts

Gold plated phono jack line inputs

Hum cancellation on unbalanced line inputs

Transformer isolation for unbalanced line inputs

Balanced mono output for unbalanced mono or stereo line inputs

Related Questions and Answers

Q: 1. can this be used with an XLR mic going into an audio interface, such as a Focusrite Scarlett?

A: Yes, while the Focusrite family can accept a wide range of microphone input voltages, this device can provide additional attenuation. If the microphone is being over-driven in a particular sound field, this will not cure that problem. It is preferred that high attenuation not be introduced on the input side and then amplified back up by the pre-amplifier as the signal to noise ratio will suffer.

Q: 2. Is this transmitter universal to all Bose S1 Pro+ speakers in range?

A: Yes, the Bose S1 Pro+ Wireless Mic/Line Transmitter (XLR) will work the Bose S1 Pro+ Wireless PA System (B&H # BOS1PROPWPAS) as a plug-in XLR transmitter with any dynamic or self-powered microphone. Please note that this transmitter is not compatible for use with the original Bose S1 Pro (B&H # BOS1PSWB) which does not include a compatible wireless microphone receiver.

Q: 3. Is this product TAA complaint?

A: The RDL STA-2A Dual High-Gain Line Amplifier Made in the U.S.A. and is TAA Compliant.

Q: 4. I don't need stereo for DSLR XLR adaptor cable. Will this still work for basic audio from a Sennhesier mic?Sescom SES-DSLR-ST-MIC XLR Stereo Mic to DSLR Audio Input Adapter Cable (10')

A: The Sescom SES-DSLR-ST_MIC is actually an output cable designed to output audio to PA systems from small cameras and recorders with a 1/8 output. In order to connect a standard dynamic or battery powered mic to a DSLR, you can use a standard XLR cable to run the length, and an adapter such as the Kopul LMT-100 to input into the DSLR. a href= http://bhpho.to/1yMIinD target= _blank http://bhpho.to/1yMIinD/a

Q: 5. Does this Wall Mount work with Condenser Mics that require phantom power?

A: Yes it will pass phantom power if your mixer has Phantom power or you purchase the phantom power injector module from RDL

Q: 6. Will this impedance match 3.5mm input to 600ohm output?

A: The RDL RU-MLD4 is a distribution amplifier capable of splitting a mic/line signal four ways without signal loss or depreciation. It unfortunately will not match the impedance of a 3.5mm input to a 600 ohm output.

Q: 7. Are there installation instructions?

A: Yes to change the Epson Roller Assembly Kit for WorkForce DS-760 & DS-860, it is on page 63-75 in the manual. The link for the manual is, https://bit.ly/3M49Lvk

Q: 8. this amplifier is 110 or 220v ?

A: The RDL RU-MLD4 - 1x4 Mic/Line Distribution Amplifier does require a 110 or 220V power source but rather uses a 24 to 33 VDC @ 80mA source via terminal block wiring or optional power supply. The RDL PS-24AS Switching Power Supply (BH #RDPS24AS) is available as a separate item for use with the RU-MLD4 and specifies compatibility with source connections between 100-240VAC: https://bhpho.to/39KBnoY

Q: 9. Is this transmitter compatible with the Sennheiser XSW-D system?

A: No, the Bose S1 Pro+ Wireless Mic/Line Transmitter is not compatible with any other brand of wireless equipment.

Q: 10. Does this roller kit apply to the FF-680W?

A: Yes, the Epson Roller Assembly Kit for DS-530, ES-400, and ES-500W Scanners is also compatible with the FastFoto FF-680W Photo Scanner from Epson.