The red FotodioX GoTough Extender Mount for GoProfrom FotodioX GoTough Extender Mount for GoProis an aluminum extension mount that adds an extra 0.8" of length and an additional pivot point when mounting GoPro housings and frames, without changing the direction of the camera. It features a built-in tightening thread for GoPro thumbscrews and is designed to be durable while remaining lightweight.

Extends Mount by 0.8"    Adds an Additional Pivot Point    Maintains Direction of Camera    Built-in Thumbscrew Threading    Aluminum Construction

• Compatible with GoPro housings and frames
• Adds an extra 0.8" of length and an additional pivot point without changing camera's direction
• Built-in thumbscrew tightening thread
• Aluminum construction

Related Questions and Answers

Q: 1. Is this compatible with Hero5 session?

A: Yes it is: Compatible with All GoPro Camera Models]

Q: 2. The GoPro mount that is on the bottom of the Gooseneck (the ball joint) broke, Is there a replacement available for that part?

A: Unfortunately, B&H does not supply these parts. GoPro has asked to tell you to contact them directly for service. Their email is support@a href= http://gopro.com target= _blank gopro.com./a

Q: 3. Will this mount stick well to the dashboard of a car too?

A: This product works best on windows or perhaps the exterior of a car. Some dashboards are made of materials that do not work well with suction cups so you'd have to test it out to know for certain.

Q: 4. How strong is this? I'm looking to attach a few GoPros to an airplane. Any suggestions if this is too weak for that?

A: While this is a strong clamp we do not recommend this or anything else for connecting the GoPro to an airplane. That would require a custom installation.

Q: 5. How easily are you able to remove the mount after use/change its location on the vehicle?

A: I have the GoPro suction mount. It is very simple to attach, remove, relocate. Position the mount and camera where you want it. Press the center of the mount firmly into the windshield, then flip down the lock lever, done! To remove, lift up the lock lever, then with your finger tips, peel up the edge of the suction cup. This will cause it to release from the windshield. Mount works great. TIP: get an assortment of GoPro mount adaptors and extensions for different mounting situations you will inevitably encounter. Good luck...

Q: 6. What size pipe will this clamp fit around?

A: Clamps around any bar from 1.3" to 2.1" (34.25mm - 54.5mm) in diameter.

Q: 7. If I have it in the outside of a car going 70 mph is it strong enough?

A: Yes it is: Mount Proven at Speeds of 150+ mph Maximum holding strength requires attachment to a clean surface

Q: 8. does it fit the Hero 4?

A: Yes, BUT I found it to fit a little snug if you're using the frame to mount your gopro. When I used the frame, it squeezed it a little too much to the point that the button pass-throughs did not function properly. Would be the same with either the gopro 3/3+, most likely. But if you're using one of the plastic enclosure housings, should be fine for any gopro.

Q: 9. The Pivot thing on the middle bottom in picture #1. Does that part have a name? I need a replacement for my Gopro mount. I do not like the long arm.

A: Unfortunately, these parts are not listed for individual sale. It seems that GoPro only has the entire kit available.Fear not, there is a growing support industry providing GoPro replacement parts. In may instances these are made of aluminium for durability. You might look at this B&H catalog listing of parts for GoPro mounts.http://bhpho.to/1IcsrlpMore specific to your request, please consider the attachment set below. I believe it has the part you wish.

Q: 10. Will this fit on Gopro hero 7 black?

A: The FotodioX GoTough Replacement Lens Cap for HERO3+/4 Dive Housing will not fit the Hero 7.