Expand your palette of possibilities by adding stomp boxes to your modular setup with the intellijel Stomp, a Eurorack module with an effects pedal send/return, expression control, and a built-in LFO. Stomp enables the modular synthesist to interact with the impressive assortment of delays, choruses, flangers, phasers, fuzz boxes, tremolos, wah-wahs, amp simulators, compressors, and pitch shifter pedals available to guitarists. Stomp supports your pedal's expression pedal input if it has one, and features a built-in LFO to modulate your expression pedal's input.

Conversely, guitarists can plug their guitar directly into Stomp's RETURN jack, giving them access to the myriad filters, ring mods, wavefolders and—most importantly—the near-infinite CV modulation delights inherent in Eurorack. The module includes a power ribbon cable.

Robust 1/4" TS I/O for Send/Return    1/4" TRS Expression    Class-A Triode Emulator on Return Jack    Level Shifter and Impedance Converter    Separate Gain for Send and Return    Supports Instruments & Line Level Inputs    Phase Reverse on Return Input    Internal LFO    Includes Ribbon Power Cable

• Robust Neutrik 1/4″ TS connectors for the SEND/RETURN and TRS for the Expression interface
• Signals arriving at Stomp’s RETURN jack pass through a Class-A triode emulator, allowing for some tubelike overdrive at high-gain settings.
• SEND output is normalled to RETURN input, so even without 1/4″ cables you can route Eurorack signals through the FET stage for coloring.
• Stomp is more than just a simple level shifter—it’s also an impedance converter, which provides proper drive and loading for any FX pedals or instruments you connect.
• Separate gain controls on both the SEND and RETURN. This enables you to adjust the level of any audio being sent to the FX pedals as well as any audio coming back into the modular. Not only does this allow you to optimize the signal-to-noise ratio, but by significantly boosting the RETURN level, you can achieve some pleasingly overdriven tones.
• Supports both PEDAL/INST and LINE levels via a front-panel switch.
• Use Stomp’s RETURN circuit as a direct box for connecting any instrument.
• The high-input impedance of the RETURN circuit allows it to be used as a piezo pickup preamp for acoustic instruments.
• Use Stomp in the studio as an active reamping device to play prerecorded tracks back through guitar amplifiers or pedals.
• All inputs are protected for minimum RF interference.
• Return signal can be phase inverted for use with those pedals or effects types that invert phase.
• Low SEND output impedance for driving long cables, lower noise, and minimum interference from outside sources.
• The Expression Pedal Output converts analog CV sources (or the internal LFO) into an output compatible with most stompbox Expression inputs.
• If the internal LFO is set to 0 Hz (full CCW), the EXPR knob can be used as a manual expression pedal control level.

• 8 HP Eurorack format module
• Maximum depth: 1.4" (35mm)
• Includes power ribbon cable with Eurorack power headers
• Power consumption: +12V: 47mA, -12V: 13mA

Related Questions and Answers

Q: 1. I bought a Behringer FX2000 processor. How do I hook it up to the A&H Zed 12FX??

A: https://www.allen-heath.com/media/AP7085_3-ZED12FX_ZED16FX_ZED22FX-User-Guide-Issue-3.pdfThe above link will take you to the User Guide of ZED12FX and other similar models from Allen & Heath. Study the guide for information.If you plan to connect the Behringer or other external FX units to the ZED, we recommend doing so by patching the unit to the ZED mixer through a post-fader AUX send. Do this by using (3) unbalanced or balanced 1/4 cables (guitar cables). Use balanced cables if the distance is long, otherwise for short distance, unbalanced cables are fine.Take Cable #1 and run it from the ZED FX send to the FX2000 mono (L) input. This is usually on the rear panel of the FX unit. Take Cable #2 and Cable #3 from the L and R outputs of the FX2000 (on rear panel) and connect these to one of the STEREO input channels on the ZED. Input a signal (microphone for example) into a channel on the ZED.Now, be sure to turn up the knobs and faders on the ZED's channel send and Master section to hear your FX2000's effect on the mic.Understand that with this method you are taking your signal out of the ZED to the FX2000 and then back into the ZED.Read the User Guide for more details. If you need further assistance, please contact your salesperson and ask for support. There are qualified and trained sales people at B&H to assist you.

Q: 2. Is the digital I/O 24bit? Any details about the DAC on the Notebook series?

A: USB:Sample rate 44.1kHz, 48kHzFrequency response20Hz 20kHz +/-1.5dB

Q: 3. Will this also stop the ronin-s from drifting over long periods of time for instance during a timelapse?

A: This product is designed to allow the gimbal to react more responsively to quick movements, providing a better stability along the horizon. We are not aware of any specific impact it will have on drifting.

Q: 4. Can I buy the magnetic adapter from B&H? Please provide link.

A: Please see attached link for BH #HAHLM600CL • MFR #HL-MODULE-600CLAMP and for B&H # HAHLM360CL MFR # HL-MODULE-360CLAMP 360: https://bhpho.to/3oeaGuS 600: https://bhpho.to/3pN8Scv

Q: 5. Does this work with the Ronin SC?

A: Unfortunately, th DJI Ronin-S External GPS Module is only compatible with the DJI Ronin S as the connection type is a 4 pin connector specific to the Ronin S.

Q: 6. Does this come with a tripod stand?

A: A tripod stand is not included. It will come with the contents seen in this photo our website https://bit.ly/3scTEPx

Q: 7. Do u guys have a case for ALLEN &HEALTH 12 FX ZED

A: Sorry, cases are not offered for ZED mixers. However, if you'd like to have a case manufacturer build a custom case, the dimensions of the mixers are found in our user guides. Go to:https://www.allen-heath.com/media/AP7085_3-ZED12FX_ZED16FX_ZED22FX-User-Guide-Issue-3.pdf. Thanks.

Q: 8. what is the gear belt size/ dimension? can't find replacement belt

A: unfortunately the manufacturer does NOT provide this information

Q: 9. Remote available?

A: The Falcon Eyes SO-68TDX II LED Soft Light with Special Effects does not offer a remote control at the moment, as an alternative we may offer https://bhpho.to/2FIqpAw with additional https://bhpho.to/4a16oih or https://bhpho.to/4a6eVkg.

Q: 10. I see the GPS module is compatible with the Ronin 4D. When used together, will it write GPS metadata into the 4D video files?

A: DJI does not mention that you will be able to receive metadata. DJI says it allows you use the DJI Ronin 4D with the Ronin-S External GPS Module, it can enhance the stabilization performance of the gimbal roll axis during rapid acceleration.