Add a space-saving VCO or LFO to your rig with the intellijel VCO 1U, a triangle-core, syncable, multi-waveform analog oscillator and LFO in a compact form factor. With four waveform outputs including sine, square, triangle, and sawtooth, the VCO 1U provides rich analog tones and precise control. Use it as a utility modulation source or as a primary sound source.

Sine, Triangle, Square and Sawtooth    Pitch Input for 1V/Oct Tracking and FM    Sync Input for Hard Sync    VCO / LFO Switch    3-Position Octave Switch    Pitch Knob with 3-Octave Range    Bicolor LED for Triangle Core Rate    Includes Ribbon Power Cable

• Four simultaneous pure waveforms:  Sine, Triangle, Square and Sawtooth
• Pitch input for 1V/oct tracking and FM
• SYNC input for Hard Sync. This input has a comparator so that you can use a variety of waveforms as triggers.
• Switch to select VCO (audio) or LFO range of operation
• Three position Octave switch to jump pitch up or down by two octaves
• Pitch knob has three octave range in VCO mode (extended to seven with the octave switch) and seven octave range in LFO mode (extended to 11 with the octave switch).
• Bicolor led indicates the state of the triangle core rate

• 14 HP Eurorack format module (1U)
• Maximum depth: 1.5" (37.5mm)
• Includes power ribbon cable with Eurorack power headers
• Power consumption: +12V: 19mA, -12V: 16mA

Related Questions and Answers

Q: 1. What is the image quality like converting HD-SDI to HD Component? Are there any artifacts or a loss of resolution? I have an HD CRT that I'd like to use, but it only has analog HD inputs. Cheers!

A: HD-SDI Digital HD was a step up in image quality over Component Analog HD. So in a critical analysis, yes, you will see a slight difference. But for casual use, there is no loss in quality to the degree that it would interfere with your use or enjoyment of your CRT display. After all, it was what we had for years and were quite happy with it.

Q: 2. Can I quickly switch input selection from the front panel? In other words if I have one feed into sdi 1 and another feed into sdi2 can I flip them. I know it's not a switcher

A: This converter is a single input device. Multiple inputs are present for signals that may need multiple connections to function.

Q: 3. Will this take an analog composite signal from let's say a hi8 (576i) and up convert it to 1080 and up?

A: Yes, you can use this converter to upconvert an SD analog composite signal to 1080 HD-SDI.

Q: 4. Can I use the Teranex Mini SDI to distribute Genlock?

A: No. All reference signals are analog and not digital. You would need an analog Distribution Amplifier.

Q: 5. What SDi signal inputs will this work with? 1920x1080i 59.94?

A: The following HD Video Standards will work: 720p50, 720p59.94, 720p60, 1080p23.98, 1080p24, 1080p25, 1080p29.97, 1080p30, 1080PsF23.98, 1080PsF24, 1080PsF25, 1080PsF29.97, 1080PsF30, 1080i50, 1080i59.94, 1080i60 1920x1080i 59.94 is compatible.

Q: 6. What is the latency of this unit?

A: Teranex Mini SDI to HDMI 12G currently has a one frame delay when Instant Lock is turned OFF but we are looking into doing an update in the future which will result in a few lines of delay only. If the Instant Lock feature is turned ON, the delay could be up to 2 frames.

Q: 7. Will this convert a 35mm film camera output (analog) to SDI signal (Digital) ?

A: No, this is a converter to go from SDI to analog. Here is a converter that will convert from analog to SDI: https://www.bhphotovideo.com/c/product/558906-REG/Blackmagic_Design_CONVMAAS_Mini_Converter_Analog_to.html?sts=pi&pim=Y

Q: 8. I need to convert analog video on a BNC to SDI on a BNC. Can I put analog BNC on the Y connector input and will it convert it to SDI?

A: No-Sorry this unit will convert SDI to analog. They do make a unit to do what you need. Blackmagic Design Mini Converter Analog to SDI B&H # BLASDIMC MFR # CONVMAAS2

Q: 9. Can I connect my atem to this and send vga out to existing projector signal ?

A: This device will give you an analog composite or an RGB component output. We use this converter to feed the component input of our projector and it works great. If you only have a VGA input on your projector, you will need to convert the component signal to VGA before you can use it on your projector.

Q: 10. Can one encoder send to multiple decoders?

A: yes