The 9.84' Global Truss Straight Segment F32 I-Beam Truss System 9.84'is designed for use in entertainment venues, trade shows, theater setups, presentation booths, large structures, and more. Made of EN-AW 6082 T6 aluminum alloy, this truss segment is designed to resist corrosion and features 0.78" (20mm) braces. Measuring 1.97" (50mm) in diameter and with a wall thickness of 0.08" (2mm), this segment is also TÜV certified.

For Entertainment Venues & Trade Shows    Made of Corrosion-Resistant Aluminum    1.97" Diameter with 0.08" Wall Thickness    TÜV Certified

Related Questions and Answers

Q: 1. Does this bracket work with this tripod Magnus PV-3310 ? I am a little concern that they may not work together. Here is my concern.The mount of the tripod, where you attach your camcorder to the tripod, has 1 screw and 1 little BLACK pin that can be pushed up and down. (Note: this little pin will go into a hole at the bottom of the camcorder when you attach your camcorder to the mount.)Now, could the knob at the bottom of bracket overlap with that little BLACK pin on the mount of the tripod when I try attach or screw the bracket into the tripod ?Thanks.

A: Sorry, I can't help you because I just received this bracket and haven't even taken it out of the package... plus, I won't be using it on a tripod... sorry bout that! MikeLago Vista, TX

Q: 2. Will this attach to a tripod? Also, I am assuming you can remove the cold shoe and just have two screws to attach to? Thanks!

A: Hi Joe. Yes this will attach to a tripod. The version I purchased does not have a cold shoe attached there is only a screw. This screw then attaches to your camera and the tripod mount is then screwed into the bottom of that screw. The screw which moves attaches to, in my case, a motion/lightning sensor. Ken

Q: 3. Can I mount both a camcorder (Sony HDR-CX455) and the Rode VideoMicro Compact On-Camera Microphone to a tripod, using this bracket ?

A: Yes. The Sony is 4.8 wide and the bracket is adjustable to accommodate that camera width and fit the Rode microphone with the deadcat wind muffler and still have some room for adjustment.

Q: 4. Can this track be used at shorter lengths? 4' for instance

A: Yes, this offers three 4 foot sections. You do not need to use all 12 feet of track.

Q: 5. Is this plastic or metal like the bevel cutter?

A: The Logan Graphic Products 701-1 Straight Cutter Elite is made with resin.

Q: 6. Will this bracket provide enough clearance to be used with Leica M's?

A: Just an update: This is NOT compatible with Leica M's. FInd something longer.

Q: 7. Does it have a trip switch so as not to overrun the rail(s)?

A: The CAME-TV Power Dolly System for Tripods with 8 Straight & 12 Curved Rails is calibrated on start up in order to set the minimum and maximum points on the rail, but does not have a trip switch to prevent rail overrun.

Q: 8. Which Vello cold shoe would you use with this product? There is a Vello shoe for about $6.00 and another for around $8.00. Which one is best? Would be using with a Nikon SB 400 or SB 600 attached to a Nikon D90 or 7000 with battery pack(s).

A: If you wanted to replace the cold shoe that is included with the Vello CB-600 bracket, this Vello model would work well:Vello Universal Accessory Shoe MountB&H # VECS ? Mfr # CSIt would interface directly with the 1/4-20 screw, also included with the bracket.

Q: 9. i use foam board 9-12 mm.. can i use foamwerks rabbet, straight bevel, and straight cutter??

A: The straight cutter will do both, the rabbet cutter will do up to 4mm and the straight bevel will do 12mm and the bevel will do 4mm.

Q: 10. is this bracket compatible with the sb900 and D200 nikon?

A: We have the SB600 and SB700. Very compatible with these flashes which have the same flash shoe as the SB900. We have the Nikon D90 and D7100 so I can't comment on the compatibility with the D200.