Keep your laptop protected with HP 3-Year Onsite Support Plan for M603 Printersfrom HP. Providing three years of coverage, this manufacturer support plan provides next business day onsite hardware support following remote diagnosis. Replacement parts and materials are included in the support plan, as are formal escalation procedures and management and access to electronic support information and tools.

Please note, to take advantage of this warranty, your hardware must currently be under its native warranty. Service starts on the date of your hardware purchase, and service levels and response times may vary depending on your geographic location. Please be aware that external displays are not covered.

For HP LaserJet M603n & M603dn Printers    Manufacturer Support Plan    Next Business Day Onsite Support    Includes Replacement Parts & Materials    HP Remote System Access and Support

In-person repairs, parts and service will arrive at your door the next business day. HP experts are on the job nine hours a day, five days a week. Please note, service levels and response times may vary depending on your geographic location. Service starts on date of hardware purchase.

Know that your hardware will be good as new as soon as possible thanks to HP's knowledgeable expertise and efficient service and support.

HP support specialists are always ready to assist in whatever way the situation calls for, whether it's remotely over the phone or in person.

Related Questions and Answers

Q: 1. Hi, can we print 2 4x6 with the 8x6 paper?

A: I am not entirely sure as I only purchase the 4x6 size

Q: 2. how do u know or what are the difference between the Rx1 paper and the new Rx1Hs paper?

A: Gray cap on the end of the ribbons receiving roll is RX1HS. Yellow is RX1

Q: 3. Can the RX1 print 6X8 prints using the 4x6 media? Does it just cut them at a longer length?

A: No, it only prints 4x6 or 2x6 for Photo strips. Thats just a 4x6 split down the middle. Printer will cut it for you.

Q: 4. Is this stand compatible with Epson F570?

A: Yes it is compatible with the F570.

Q: 5. After mount the paper and ribbons 4x6 can we change for paper and ribbons 8x6 before the paper finish or I have to wait to finish one size to change for the other size?

A: You absolutely can. Two VERY important things to keep in mind.1. Be sure the roll of paper maintains it's shape - be VERY careful when pulling the end caps off. If the roll is off my as much as 1/4 , the paper will jam and your ribbon will break.2. Change the ribbon at the same time - this is just for convenience - then you avoid the potential of haveing 2 changes during one event. You always get a ribbon with a roll of paper so it just makes sense to keep the roll with the paper.

Q: 6. The description says its only compatible with 3 sony cameras. Would this work with any sony camera that uses an fz100 battery?

A: Under the Compatibility section we list the current cameras this will work with. It is more than three at this time.

Q: 7. Will this work on an Epson P8000?

A: The Epson 320GB Internal Hard Drive for SureColor P7570 & P9570 Printers is not compatible with the P8000. The P8000 needs Epson part number C12C848031, which is not made anymore.

Q: 8. Does the kit include the external battery?

A: This OnSite Power System Kit does not include a battery, but the Tether Tools ONsite USB-C 30W Battery Pack (9600mAh), BH # TESDAC30 can be used. https://bhpho.to/3Ls5Nui

Q: 9. I have not use the 6x8 media on my RX1 Printer, does it require a different spool so I can use the 6x8 or can I use the same spool I am using for the 4x6?

A: Same spool

Q: 10. When camera/coupler/Tether Tool is operating, suggestions of how to keep battery drain from exceeding the simultaneous charging? I have found it will not do both at the same time. Thanks.

A: It works for me. Keep in mind you have to use a power bank or charger that outputs at least 2 amps (the one i use is 2.1 amps). I tried with a power bank that only outputs 1 amp initially and that gave me the same problem as you have.