This 9.84' Global Truss Straight Tube Segment Conical Connector 9.84'from Global Truss Straight Tube Segment Conical Connector 9.84'adds extra length to 2" truss sections. One end is 2" diameter female and the other has a conical connector.

Fabricated by Certified TUV Welders

Related Questions and Answers

Q: 1. Are there any grids available for this snoot?

A: Broncolor does not make a grid for this snoot.

Q: 2. What metal is this product made with?

A: It is made of aluminum.

Q: 3. Will this attach to a tripod? Also, I am assuming you can remove the cold shoe and just have two screws to attach to? Thanks!

A: Hi Joe. Yes this will attach to a tripod. The version I purchased does not have a cold shoe attached there is only a screw. This screw then attaches to your camera and the tripod mount is then screwed into the bottom of that screw. The screw which moves attaches to, in my case, a motion/lightning sensor. Ken

Q: 4. Does this bracket work with this tripod Magnus PV-3310 ? I am a little concern that they may not work together. Here is my concern.The mount of the tripod, where you attach your camcorder to the tripod, has 1 screw and 1 little BLACK pin that can be pushed up and down. (Note: this little pin will go into a hole at the bottom of the camcorder when you attach your camcorder to the mount.)Now, could the knob at the bottom of bracket overlap with that little BLACK pin on the mount of the tripod when I try attach or screw the bracket into the tripod ?Thanks.

A: Sorry, I can't help you because I just received this bracket and haven't even taken it out of the package... plus, I won't be using it on a tripod... sorry bout that! MikeLago Vista, TX

Q: 5. i use foam board 9-12 mm.. can i use foamwerks rabbet, straight bevel, and straight cutter??

A: The straight cutter will do both, the rabbet cutter will do up to 4mm and the straight bevel will do 12mm and the bevel will do 4mm.

Q: 6. Will this bracket support a Godox VING V860IIC TTL Li-Ion Flash firmly?

A: Yes, the QuickDraw/Straight Bracket & TTL Cord Kit will support a Godox VING V860II C TTL flash firmly.

Q: 7. Can this bracket work with Rode VideoMicro Compact On-Camera Microphone , which is also sold here at a href= http://www.bhphotovideo.com target= _blank www.bhphotovideo.com/a ?

A: YES! I use the Rode microphone with this and a clip to hold my cell phone when filming. I have also used it with a small DSLR to shoot video when I wanted the microphone off to the side slightly. I mounted this bracket onto a Joby Gorillapod to hand hold and mount to a light stand for shooting BTS footage.

Q: 8. Will this bracket provide enough clearance to be used with Leica M's?

A: Just an update: This is NOT compatible with Leica M's. FInd something longer.

Q: 9. What is the beam angle with snoot attached?

A: The resulting beam angle is approximately twenty degrees but will vary based on placement/distance.

Q: 10. Which Vello cold shoe would you use with this product? There is a Vello shoe for about $6.00 and another for around $8.00. Which one is best? Would be using with a Nikon SB 400 or SB 600 attached to a Nikon D90 or 7000 with battery pack(s).

A: If you wanted to replace the cold shoe that is included with the Vello CB-600 bracket, this Vello model would work well:Vello Universal Accessory Shoe MountB&H # VECS ? Mfr # CSIt would interface directly with the 1/4-20 screw, also included with the bracket.