[198 lb] The screen was simple to mount (we used lag bolts and attached the screen to a wall.) The screen did not come with instructions on how to install the switch for a 120v motor...complicated the electrical install was inconsistent wire colors on the switch and the screen. After consulting an electrician and enduring his derision for working with this product - he correctly intuited the correct wiring configuration. A big thanks to the customer service at B&H. We ordered the screen 2 weeks from a graduation. The shipper lost the screen for nearly a week, without informing us. I contacted the shipper, who responded with a long distance shoulder shrug - explaining they would look for it again. Unable to motivate the shipper, I called B&H - they got involved, and the screen was in my driveway 36 hours later. Thanks B&H.

[HDTV / 16:9] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projection screen/case up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem!

[None] Looking forward to getting all of this stuff together

[None] I have used this Da-Lite screen for the past 3+ years. This is actually my second purchase. Compared to some brands and products, the price is reasonable. The design is solid, great for portable use and easy to setup. However, it weights close to 70 pounds. A great product nonetheless.

[None] This was the forth 9X12 dalite screen that we have purchased. We also have several 6X8's. We use them for PR meetings in various churches and schools around the US. Dalite screens are excellent! The newer fast fold frames are bigger and built stronger and the easy release latches work extremely well and you no longer need to fight the frame to put it together and take it apart. I often get assistance from a local person at the meeting and they are always amazed at how it all folds together and fits into the case. THe cases are much too big, I think and I have taken them and cut them down so they don't use up so much storage space.

[None] I used this screen in a small conference room and it was very simple to instal.

[White] I installed in my living room in between ceiling joists. It works great. I use it with a Panasonic HD projector. It impresses everyone who walks in the room. Has a clean appearance when retracted. Note: it didn't come with a 12v trigger as both the B&H customer service rep and myself thought it did. We both misunderstood the description (it's optional.) The part was available at Da-Lite for $80 and came with no instructions. I got it to work after a few emails and chats with da-lite. Also, I ended up placing some holes in the top of the case to mount using 8 Lag bolts into the 2nd story floor structure. All the hardware that comes with it assumes you will have access to hang it from the top which requires access via the side while it's in it's final position. I was putting it in a hole the size of the case in my finished ceiling so that method would not work ( I would have had to remove and re-install a lot of drywall). I knew this before I purchased by reading the installation instructions so no worries just a fact and maybe a consideration for future changes to the case or just the directions.

[198 lb] This screen was installed in a small conference room with an NEC projector. The screen can be wall or ceiling mounted, and this flexibility came in handy when we had to switch to a ceiling mount at the last moment. The screen presents very well, and is unobtrusive when retracted. The tensioning system works nicely, and we didn't have to change any of the factory settings for the drop. I would have liked to see some additional mounting holes for attaching the screen to studs in the wall, so the installer has more options for wall mounting.

[186 x 13 x 10"] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projector up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem!

[Non-tensioned] This Screen was easy to install. It took 3 people and 2 ladders to get the job done. The remote is really not needed but i opted to install it as well. The motor runs really smooth. The screen is nice and wide. A really good buy.