The TRENDnet TEG-S82g 8-Port Gigabit GREENnet Switchfrom TRENDnet TEG-S82g 8-Port Gigabit GREENnet Switchfeatures eight Gigabit Ethernet ports for fast, secure transfer of data. Take advantage of enhanced data transfer speeds of up to 2,000 Mbps in full-duplex mode providing sufficient network bandwidth for activities such as streaming HD content, transferring large files, streaming music and more.

This TRENDnet switch also comes equipped with 16 Gbps switching capacity for advanced network configurations. A 16 Gbps switching capacity offers better total throughput than broadcast networks as the traffic is spread across multiple physical links rather than direct connections throughout the network. The 256 KB data RAM buffer helps to ensure a smooth flow of data by allowing for timing corrections within the data stream.

8 x Gigabit Auto-MDIX RJ-45 Ports    Gigabit Ethernet Data Speeds    16 Gbps Forwarding Capacity    256 K Bytes Data RAM Buffer    8 K Filtering Table Entries    9216 Bytes Jumbo Frame Support    Integrated Diagnostic LEDs    Sturdy Metal Switch

GREENnet Technology reduces power consumption

Store-and-Forward switching architecture with non-blocking wire-speed performance

IEEE 802.3x Flow Control for full-duplex mode

Back pressure Flow Control for half-duplex mode

Related Questions and Answers

Q: 1. Is this compatible with the Canon G16?

A: Yes, the Canon RS-60E3 Remote Switch would be compatible for use with the Canon PowerShot G16 Digital Camera.

Q: 2. How do you factory reset the adapters?

A: On the bottom of the device you should see a reset button, stick a small pin inside and hold down for 10-15 seconds. This should reset the device to factory settings

Q: 3. Can one assign different devices on the LAN to specific WAN connections, eg via a routing table?

A: You can setup routing tables with the TRENDnet TEW-829DRU AC3000 Wireless Tri-Band Gigabit Router BH #TRTEW829DRU.

Q: 4. Will this work on a Pentax K70?

A: Yes, the Pentax CS-310 Cable Switch is compatible for use with the Pentax K-70 DSLR camera.

Q: 5. Will this work with Aputure 600 d/c/x?

A: Yes. The following is based on a 3pin Bowens mount system.

Q: 6. Hi Guys, the TC-NT2 you have pictured is the discontinued Version 1.0 . Trendnet have updated this to Version v1.1R , is this the one you are shipping?

A: Hi Guys, it looks like you have updated the picture to the Version v1.1R now.

Q: 7. How long is the cord?

A: The cable is 2.6' / 80cm long.

Q: 8. Is this compatible with any Canon Powershots (Elph, etc)? I'm trying to find a small point and shoot where I can use a remote switch.Thanks

A: You could look at the G16 (B&H # CAPSG16). It would be a Canon PowerShot that is compatible with the RS-60E3 Remote Switch. None of the Elphs are compatible with a remote shutter release.

Q: 9. How to factory reset the adapters?

A: Hi Erby! Thanks for your interest in TRENDnet! Press the reset button on the bottom for 1 second. Resets device to factory defaults settings (All LEDs will turn off and on again). Note: Will reset to the factory default private network name “HomePlug AV”. Hope this helps! If you have any more questions, you can always respond directly to this thread and someone will be happy to try and help answer any additional questions you may have! Have a great day! Adrian TRENDnet CS

Q: 10. Canon Remote Switch for 80D

A: I believe the Canon 80D has an E-3 type connector which will require the RS-60 E3 Remote switch. Check your manual for the connector type. B and H carries the RS-60 E3.