The black SF8-CPT-JNC2 8" Poke-Thru with Cover and AC Set from FSR is a complete SmartFit fire rated floor box assembly. It includes an 8" floor fitting, 2 dual 20-amp pre-wired AC outlet sub plates, an EMT fitting adapter with 2 1" stubs, a cover assembly, and a junction box.

The SmartFit series features recessed mounting bracketry to accommodate a wide assortment of power, data and audio video connection options. The entire door cover swings open 180° and the two smaller cable access doors fold down for cable egress while the cover door is secure. The cover technology exceeds UL scrub water testing requirements.

All Fire-Rated Poke-Thrus are Buy American compliant.

Fire-Resistant for 2-Hours    180° Access Door Opening    ADA Compliant Flange Height    Power Wiring Junction Box Included    Complies with UL514A Scrub Water Test    Cover Loaded Rate at 1000 lb    ULC and cULus Rated    Buy American Compliant

2-Hour fire rating

Power wiring junction box included

Drop down cable access doors to reduce trip hazards

NEMA WD6 device spacing

ULC and cULus rated

Related Questions and Answers

Q: 1. Can these strips be used for mounting 13" x 19" prints?

A: Yes, you can use the Lineco "See Thru" Mounting Strips - Pack of 60 to mount a 13" x 19" print.

Q: 2. Will this trigger more than one flash unit or do two receivers need to be purchased?

A: A receiver for each flash/strobe needs to be purchased.

Q: 3. There are two sides of adhesive - does it stick to the mat and mat board?

A: You apply these strips to a backing board with their adhesive tape -- for your purposes the adhesive tape is 1-sided, being already attached to the firm plastic strip.The adhesive doesn't cover the full width of the plastic strip; it leaves perhaps 1/5 of plastic free to act as a trap for the item being mounted. There is no adhesive in direct contact with the mounted item's surface.This is ideal for use on a backing board where glass and/or matting will keep the artwork from falling out of the strip's thin rim of plastic. It wouldn't work for a large paper item which lacked a glass in front -- the paper's weight would pull it out of plastic edges, I suspect. The role of this is to prevent artwork from shifting around after it matted and framed.Note that the adhesive holding the mounting strip is outside the dimensions of the artwork: the backing board needs to be around an inch wider than the artwork to have room for the strips.

Q: 4. I purchased the 3 light kit and two additional transmitter and receiver sets. I noticed that when I use the test button, both strobes fire off fine, but when taking photographs, sometimes one of the lights will not trigger. Is anyone aware of similar issues? Using a Nikon D7100.

A: Always have backup batteries for this product because it can go at anytime. Agreed with other answer to switch up the battery and check the channel used. Also, might sound silly but make sure your wire connections/plug ins are all secure, nothing loose or adapters not fitting properly.

Q: 5. Does the on camera transmitter have an off switch or does it not consume battery when not in use?

A: No, the following unit does not offer a on/ off switch.

Q: 6. Can I use this PowerTrigger on a Nikon D7200 and Westcott Strobelite Plus?

A: Not familiar with Nikon. I shoot Cannon

Q: 7. does this come with photo papers included?

A: No, the Hahnemuhle Linen Album Cover Set does not come with photo papers.

Q: 8. hi I just bought this trigger ( impact power trigger) and is not working... I have a canon 6d and have put the transmitter on the hot shoe of the camera and the red light has not light up even though i tried the 16 channels. the equipment is new so I may say the battery is new too... the connection in the impact vsd 160 monolight is ok... could it be a problem on the camera? I also have trouble shooting with the original sync cord that came with the monolight... please any indications will help. Thanks

A: I had the same difficulties with my trigger. I sent it back to the manufacturer and they said they could not find anything wrong with it. I did try I few things to troubleshoot it including the battery but it still didnt work. Impact said they would ask B&H to refund me.

Q: 9. What is the smallest waist size it can adjust to?

A: The SHAPE On-Set AC Belt and Pouch Tool Kits belt is adjustable for a variety of waist sizes from 36 to 48".

Q: 10. Will this work for sony a7III ?

A: No, Sony uses a multi interface system for the shoe and remote. Click the link below to view; https://bhpho.to/2ED0aLJ