The black Yamaha HS5 Studio Monitor Blackfrom Yamaha HS5 Studio Monitor Blackis a bi-amplified monitor that is designed for accurate sound reproduction. It is capable of up to 70W of total output and features a 5-inch woofer and a 1-inch tweeter with waveguide that can produce frequencies up to 30 kHz. The HS5 has both an XLR and 1/4" TRS input that accept either balanced or unbalanced signals for integration into a variety of studio setups.

70W Total Output    5" Cone Woofer    1" Dome Tweeter    Room Control Response Switch    High Trim    XLR Input    1/4" TRS Input    Low-Resonance Enclosure

HS Series cabinets are designed to eliminate unwanted resonance and increase theaccuracy of sound reproduction to their extreme limit. The enclosures are constructed froma dense MDF with a damped acoustic response. HS Series engineers also employed a traditional three-way mitered-joint technique. Common to architectural design, this construction firmly anchors the corners of the enclosure to improve durability and eliminate unwanted resonance that can influence overall sound

Speaker port design can greatly influence the clarity of overall sound. Often a vortex at the either end of the port can generate air vibrations inside of the port, causing unwanted noise. By adopting a noise reduction technology that incorporates an analysis of

a visual representation of the sound, Yamaha's engineers are able to control and reduce the vortex. Through this analysis Yamaha has arrived at a port design that reduces noise up to 6dB

HS Series full-range models feature two response controls with settings that allow them to adapt to the surface acoustics of rooms of varying shape and size. ROOM CONTROL allows you toattenuate the unnatural, exaggerated low-end that can often occur when speakers are placednext to walls, while HIGH TRIM allows for more flexible control of high frequency response.For inputs, HS full-range speakers can accommodate a range of balanced and unbalanced sources such as mixers, keyboards and audio interfaces with XLR and TRS phone jacks

Related Questions and Answers

Q: 1. Does this amplifier can be used for bose acoustimass 2speaker system?

A: Yes you can. I just looked at the Bose Manual online and after you follow the directions for connecting the satelite spkrs to the main unit, you just connect the Left and Right of the main unit to the R-S202 L & R spkr outputs!!! Have Fun

Q: 2. Dynamic or Condenser?

A: The Samson HS5 Headset Microphone uses a condenser type element.

Q: 3. Is the 100W RMS or peak?

A: That would be RMS. The Yamaha R-S202 can deliver 100 W per channel continuous power at 8 Ohms.

Q: 4. I am surprised to notice that practically there is no sound until the volume is raised to 40 to 45. Is this a device problem or normal for this product?

A: It may vary somewhat depending on the connected speakers and listening mode. Try headphones also.

Q: 5. hola buenos dias,vivo en cancun,me interesa el amplificador yamaha r-s202,trabja a120 voltios?

A: 120 volt only.

Q: 6. We can possible to connect a 2 PAgoldwood 10 inch speaker 300watts in this amplifier?

A: Most likely yes, i would check the ohm load requirement on the speaker just to safe.

Q: 7. Can I use the Bluetooth feature to play sound from my Smart TV?

A: If your smart tv is bluetooth output compatible then yes.

Q: 8. Can this receiver support an EQ box?

A: Unfortunately newer current receivers like the Yamaha S202 no longer support the use of a Separate Equalizer. The same will apply to the other receiver options we have listed.

Q: 9. Does this receiver have a connection for a ground wire from another component?

A: There is no grounding terminal. try using the screw on the faceplate of your electrical outlet.

Q: 10. Can I hook a pre amp to this?

A: Yes, you can connect the pre-amp to one of its Line-in connections. I am currently using a turntable with a built-in pre-amp to a Line-in connection, works great.