The Da-Lite UTB Contour 106" HD Pro 1.1 Screenis great for any room, especially boardrooms, where aesthetics are important. It features an ultra thin bezel frame and the latest in front projection to maximize the technology of your projector.

The frame has an overall viewing area of 52 x 92" (132 x 234 cm) and will be constructed of aluminum with slip-joints at the corners. The bezel will conceal the frame, grommets and binding of the screen. The front lip of the bezel will be 0.25" (0.6 cm) all around the viewing area surface. The bezel is made of aluminum and will have an acid etched black finish.

It will be fire retardant and mildew resistant, plus standard wall-mounting brackets will be included.

Ultra Thin Bezel Frame    16:9 Aspect Ratio    Low Profile Flat Panel Design    Features HD Progressive Surfaces    Wall Mounted    Front Projection    Fire Retardant    Mildew Resistant

The UTB Contour features an ultra thin bezel frame and a projection surface that maximizes the technology of your projector

Small edge fixed frame

Low profile flat panel design 1.4" (3.6 cm) off the wall

Features HD progressive surfaces designed for 1080p, 4K and Ultra HD

Related Questions and Answers

Q: 1. Other than an additional 2 outputs, how is this different than BH #FRMSX2L? I want to be sure the internals and technology used is exactly the same as I wish to use this device not only to split a signal, but to add additional safeguards and protection to the SDI port on the RED Komodo in the event of a power surge. Thanks.

A: Both Freakshow HD Micro Split DA models are the same other than the additional outputs. Please still follow the RED SDI safety guidelines. * Preventing Damage to SDI Outputs https://bit.ly/3i0sQi9

Q: 2. Is the focal length transmitted to the camera corrected? For example, if used with a 200mm, is the combination 200mm + 1.4x converter transmitting the info 'focal length = 280mm' to the camera? (Important for stabilization)

A: It does register if you use it with a Pentax lens. It shows 420mm with my DA*300mm F4 and 140mm with my Pentax 100mm WR. Not sure about the rest. Probably so if you you a fast lens. Dont know about non Pentax lenses.

Q: 3. Will this work with a K3 as well as the listed K3 II, etc.?

A: Yes, the Pentax DA* 11-18mm F/2.8 ED DC AW lens is compatible with the Pentax K3 camera.

Q: 4. How many channels of embedded audio does this pass through? Also, what's the latency of the SDI signal if used to split a viewfinder output?

A: The Freakshow HD Micro Split 4K/12G Reclocking DA with Standard Connector will embed audio on all channels. You should experience little to no latency.

Q: 5. I own a Pentax K-3 with several lenses. Two of them are Sigma's. I am planning to use this coverter on my Sigma 70-300mm F4-5.6 APO DG Macro. Is this a viable choice to extend my capabilities? Sharpness? Loss of stops? Thank you!

A: I use the converter with a K-3 & a Pentax 300 mm F4 lens. As everything is Pentax all the lens functions are maintained and the camera recognizes the set up as a 420 lens. The set up dropped 1.6 F stops. Images are tac sharp!

Q: 6. Will this lens work with a Pentax K10 ?

A: Yes, in fact, all the lenses that I used on my K10 work just fine on my K5 and K3. This particular lens is one of my favorites. It is really sharp, has great color and even does macro - you can't go wrong.

Q: 7. Country of Origin?

A: Assembled in Vietnam

Q: 8. Will it work with Pentax K-5 and 150-450mm 4.5-5.6 lens?

A: Yes, its compatible but you will probably lose autofocus on the long end.

Q: 9. THIS SHOULD WORK WELL WITH MY NEW PENTAX SMC DA 18X270 SDM LENS F3.5-6.3 ED, CORRECT ?

A: Checked the compatibility list that came with my DA 1.4x and it does not list this lens as either compatible or Not compatible. To be sure you might want to check with Ricoh, though it does work with the 50-135 and 55-300 so I don't see why it wouldn't. You also may have to update your camera to the latest software for autofocus function.

Q: 10. Can large filter holders be thread attached to the front of this lens?

A: As long as the brand/model filter holder you own or are planning to purchase has 82mm adapter rings designed for use with the filter holder, then yes, you may attach a filter holder (with the 82mm adapter ring) to the filter threads on the front of the Pentax HD Pentax DA* 11-18mm f/2.8 ED DC AW Lens.