The 25' Kramer Electronics XLR 3-Male to XLR 3-Female Quad Style Cable is designed for microphone or line level audio interconnections. The cable uses four cores of copper, wound in two parallel pairs, to reduce the amount of electromagnetically induced noise caused by environmental factors such as AC transformers and florescent light ballasts from interfering with the audio signal.

The quad-core design can reduce induction levels by up to 90% when compared to a regular two-pair balanced microphone cable. Additionally, the cable features no-shrink, back hand-soldered XLR connectors, XLPE insulation, and utilizes a large number of thin bare copper wire strands to improve cable flexibility.

Microphone or Line-Level Audio Cable    Four-Conductor Arrangement Limits EMI    90% Less Induction than Two-Pair Cables    Thin Copper Wire Strands for Flexibility    Hand-Soldered XLR Connectors    XLPE Insulation

Related Questions and Answers

Q: 1. Can this convert unbalanced TRS to balanced XLR?

A: This adapter will not balance the microphone signal. You can use it to connect stereo 3.5mm wired microphones to XLR inputs. This version does have a transformer balanced output: https://bhpho.to/2WQbqxK

Q: 2. will it work with takstar sgc-598?

A: That adapter will work for the Takstar SGC-598 microphone, to connect to an XLR input. Since that Takstar mic is battery powered, the less costly ROVXLR adapter would also work: https://bhpho.to/3AOKIE9

Q: 3. Does this work with the Deity D3 pro microphone ?

A: No. Because the D3 is self powered you can use the regular VXLR https://www.bhphotovideo.com/c/product/387850-REG/Rode_VXLR_VXLR_Mono_Mini_Jack.html

Q: 4. Can someone describe what is connected to each 1/8 in. connection (tip. ring, sleeve) in terms of signal, power, and ground? (This would help to answer a lot of other questions.)

A: The specific TRS input wiring schematic is not available for the Rode VXLR+ 3.5mm TRS Female to XLR Male Adapter with Phantom Power Converter, however we can confirm that the VXLR+ is compatible with microphones using the 3.5mm "Sennheiser" wiring configuration for compatibility. This adapter is not compatible with microphones wired for compatibility with Sony input connections.

Q: 5. Can this allow me to use a RODE videomicGO on a SONY HXR-NX100? The Sony only has XLR inputs.

A: It should. I use it on all my cameras that have XLR inputs and it works great.

Q: 6. Sanken COS-11D Omni Lavalier Mic With a Sennheiser 3.5 EW connector work properly with this adapter please?

A: My previous answer may be inaccurate. Some COS-11D microphones are 48V Phantom and some are +3V to +10V. You will need to determine the power requirements of your microphone. The VXLR Plus provides 5 Volts.

Q: 7. Is this compatible with balanced or unbalanced XLR?

A: The VXLR+ is designed to convert high voltage phantom power used with pro balanced XLR mic inputs into much lower bias voltage (plug-in power) that is needed by many unbalanced electret condenser mics like lavalier mics and shotgun style camera mics.

Q: 8. Will this work with the Tram TR50?

A: Hello Stan, I show the TR50 as a XLR connection and therefore it would not. If there is a TR50 available with a 3.5mm TRS connector then yes, this will work for you.

Q: 9. Can I use this on my sinhieser xwd wireless lav to connect to my c100 mark 2 with the top handle attacged

A: Hello Ben. The VXLR Plus is a 3.5mm TRS Female to XLR Male adapter and converts phantom power of P48 down to plug in power (2-5v). If that's what you need to do and you have the proper connections then, yes, it should work. If you don't need power then the Rode VXLR would work just as well.

Q: 10. I'd like to use the 9V battery powered Rode Videomic (VIDEOMIC-R) to connect with a Zoom PodTrak P4. Will a standard VXLR converter work with that, or do I need this VXLR+ for it? Thanks!

A: With 9V battery installed, the standard VXLR converter will work.