The Micro Ball Head from Square Jellyfish is a lightweight (0.3 oz) ball head meant to hold cameras and smartphones under 9 oz. It can fit onto any tripod with a 1/4"-20 threaded stud.

You can pan your camera a full 360°, while the built-in tension screw will hold it in place. Two slots on the head allow you to place the camera in portrait orientation.

Load Capacity: 9 oz    360° Panning    Height: 1.5"    Weight: 0.3 oz

Tension can be adjusted with a small flat-head screwdriver by turning the recessed set-screw under the ball head.

Related Questions and Answers

Q: 1. Can this head be adapted to accept an RC2 plate?

A: Yes, you can purchase the Manfrotto clamp 323RC2; https://bhpho.to/2cjY1Xe

Q: 2. Other than the ability to use a charger, what is the difference between the Square Jellyfish Jelly Grip WX mount vs Square Jellyfish Jelly Grip mount? From the pictures on your website, it looks like the Jelly Grip may have more rotation range of motion than the Jelly Grip WX. Is that the case? Any other differences? Thank you!

A: Other than the fact the Square Jellyfish Jelly Grip WX Tripod Mount is compatible for use with the Square Jelly Grip WX 10W Wireless Charger (which we do not carry), the main difference between the Square Jellyfish Jelly Grip WX Tripod Mount and the Square Jellyfish Jelly Grip Tripod Mount for Smartphones is the WX model accepts wider smartphones up to 4 inches (10.16 cm) wide, whereas the Square Jellyfish Jelly Grip Tripod Mount for Smartphones only accepts smartphones up to 3.625" (9.21 cm) wide. Both have 360 degrees of rotation and can tilt forward and backward.

Q: 3. What is wx?

A: WX is a wireless charger by Square Jellyfish which is called the WX charger. The Square Jellyfish Jelly Grip WX Tripod Mount with Tabletop Tripod for Smartphones BH #SQJGWXTMPT is compatible with that charger.

Q: 4. Can this fit my camera tripod? Thanks

A: Yes, as long as your tripod has a 1/4-20 which is very standard.

Q: 5. Is the round, padded mounting platform "attached" to the screw, so one can loosen the ball, then use the platform as a "handle" to tighten the screw to the device? Or, must one tighten the ball and rotate the device or entire head to tighten?

A: The platform can be unscrewed from the stem, rotating the head to screw into the camera is the best solution.

Q: 6. Will it hold the new iPhone 12 Pro Max?

A: Yes, the Square Jellyfish Jelly Grip Tripod Mount for Smartphones BH #SQJLYGRTM15 is compatible with the iPhone 12 Pro Max.

Q: 7. My phone with case is 14 mm thick. Will my phone WITH case fit this mount? Thank you.

A: The Square Jellyfish Jelly Grip Tripod Mount for Smartphones accepts smartphones up to 3.625" or 92 mm wide. If your phone with a case is only 14 mm thick, it can fit in the mount.

Q: 8. I have a 17mm ball can i take this off and put it on my mount?

A: The Square Jellyfish Jelly Grip Tripod Mount for Smartphones BH #SQJLYGRTM15 can mount to any standard 1/4"-20 tripod mount. The joint ball is not meant to be user replaceable and the manufacturer does not specify the size of the ball so we would not guarantee it.

Q: 9. Is there enough fine adjustment/resolution in the ball tightness where the camera can be moved by hand but remain stable in the ball mount if let go? Or would a fluid head be required?

A: A fluid head would be better for this. One such head is the Manfrotto 502AH Pro Video Head with Flat Base, BH # MAMVH502AH http://bhpho.to/3c0ppq8

Q: 10. can I use this on the osmo mobile 3?

A: No, you cannot use the Square Jellyfish Jelly Grip Tripod Mount for Smartphones BH #SQJLYGRTM15 directly on the DJI Osmo Mobile 3.