The DB-TPS2A Active Dual Pair RJ45 Sender Module from RDL DB-TPS2A Active Dual Pair RJ45 Sender Module Blackis a two-pair audio sending module compatible with RDL Format-A twisted pair products. The DB-TPS2A features a black front-panel laminate. The DB-TPS2A module features two RCA phono jack inputs, one for the left channel source and one for the right channel source. These inputs are designed to receive standard -10 dBV consumer level signals. The input signals are amplified using studio-quality pre-amplifiers optimized for normal operating levels. The buffered left and right inputs are routed to output cable pairs B and C.

This module drives only two cable pairs, therefore it accept a signal and power from one microphone-level or line-level Format-A single-pair sender. This unit has a second RJ45 jack for an input cable. One single-pair sender may be chained with the DB-TPS2A. A single-pair sender must be set to feed pair A if it is connected together with the DB-TPS2A. The power pair and all three audio pairs are fed through both rear-panel RJ45 jacks.

The DB-TPS2A can be powered directly from a 24 VDC power supply using the detachable terminal block. Local power connected to the module is also fed to all connected remote modules. The DB-TPS2A may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED. The DB-TPS2A is designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources. The DB-TPS2A can mount in RDL WB-1U and WB-2U wall boxes, or in standard U.S. electrical boxes.

Two unbalanced -10 dBV phono jack audio inputs

Left (L) input feeds Pair B; Right (R) Feeds Pair C

Signal and Power pair pass-through on RJ45 jacks

Remote powering through twisted pair cable

Fused local power feeds all connected modules

Local power input on terminal block

Blue LED indicates module is powered

Daisy-chain with single-pair senders

Studio-Quality Precision Active Balanced Circuitry

Related Questions and Answers

Q: 1. Using inches and not centimeters to report size. Can you correct?

A: Below are correct dimensions for the Lowepro Photo Active 200 AW Backpack (Blue/Black): External: 26.5 x 16 x 44.5 cm / 10.43 x 6.29 x 17.51" Internal: 24 x 12 x 42 cm / 9.44 x 4.72 x 16.53"

Q: 2. Will this fit a gripped Sony camera and a 70-200mm lens?

A: Yes. The following bag will accommodate both pieces but not mounted together.

Q: 3. When you remove the divider system is the space usable for other storage from the top all the way to the bottom of the pack?

A: In Lowepro Photo Active BP 300 AW Backpack when you remove the divider system, the space is usable for other storage from the top all the way to the bottom of the pack.

Q: 4. will this fit a Mavic 3 Pro with the larger RC Pro?

A: Yes, the Lowepro Photo Active 200 AW Backpack will fit a Mavic 3 Pro with the larger RC Pro.

Q: 5. I see not all DSLR's fit. Will my Fujifilm X-T4 fit?

A: Yes, the Fuji XT-4 will fit.

Q: 6. Does this work for both moving coil or moving magnet phonos?

A: Unfortunately the manufacturer does not specify which cartridges are recommended, however we would recommend this unit for use with MM cartridges for best results.

Q: 7. What else will I need to go with this for my softbox?

A: You will need a monolight and an approproiate speed ring. You should also get some sandbags to prevent the stand from tipping over.

Q: 8. Will this fit a Nikon Z6, FTZ, Sigma 150-600mm and 16-28mm?

A: No, we suggest the BP300 for the extra room and much needed accessories for the lens and camera combo mentioned.

Q: 9. Is this stand strong enough to support the Impact Telescopic Collapsible Reflector Holder, weight 3lbs w. reflector attached? B&H# IMLDHT. Would be for very light studio use only, nothing outdoors. Prefer not to have use sandbags.

A: Can't say for certain, I have only used the stand to hold flash units, but I think it could easily support three pounds.

Q: 10. How big of a tripod can you fit on the side? is the pocket deep enough for a bigger tripod or is it more for a smaller one?

A: Lowepro Photo Active BP 300 AW Backpack does not have a dedicated pocket for a standard size tripod. However, you can use the mesh stretchable pocket on the side you won't be utilizing to access the equipment inside the backpack. You can attach small tabletop tripods but if you own a standard tripod you can also use the strap to secure the top of your tripod and insert 2 of the tripod legs on the side pocket. You can also use the belt strap and the bottom loop to secure a tripod on this backpack.