The EZ-PD3 Power Supply Distributor from RDL is used where power distribution from a current-limited switching power supply is needed. It is suitable for powering up to three EZ modules from a single power supply. Upon application of power, the EZ-PD3 ramps the voltage up, charging any load capacitance as quickly as possible, then switching full voltage to the load. A front-panel power switch is provided. The front-panel blue LED remains illuminated when the outputs are active.

Distribution of 24VDC power

Soft-start from switching supply

Outputs may be activated by a front-panel switch

Up to 3 power distribution points

Voltage presence indication

Reverse voltage protection

Energy efficiency by powering multiple products from a single power supply

Related Questions and Answers

Q: 1. Does this work for a Mackie Mix8?

A: This is not a compatible power supply for the Mackie Mix8 . Please contact Mackie directly for the proper replacement AC power supply (18 VAC, 600 mA): Mackie: Distributed By - Loud TechnologiesTel: (866) 858 5832

Q: 2. what’s the best way to keep this battery charged or uncharged?

A: The Celestron PowerTank Lithium should be kept at around 40-50% State of Charge to be ready for immediate use – this is approximately 3.8 Volts per cell – while tests have suggested that if this battery type is kept fully charged the recoverable capacity is reduced over time. The voltage of each cell should not fall below 2 volts as at this point the anode starts dissolving causing copper shunts to form which will cause an irreversible loss of capacity. Similarly lithium based batteries can be damaged by over charging which causes the cathode to decompose.

Q: 3. Can I run the output into an unbalanced recorder?

A: No problem - just adapt the XLR output from the ROLLS to the required input on your recorder.

Q: 4. Is there any chance this works with an 802VLZ4?

A: Yes, the Mackie 0028090-00 External Power Supply is compatible for use with the Mackie 802VLZ4 Ultra-Compact Mixer.

Q: 5. Is it possible to just buy one slide part with the prongs? I had a prong fall off and would rather not buy the whole thing is possible

A: You should contact Blackmagic Support and see what they can do.

Q: 6. Does this work for the 402-VLZ3?

A: Yes. Key Features For 402VLZ3, 402VLZ4, 802VLZ3, and 802VLZ3 Mixers

Q: 7. Hello, will it fit a Tapco mix 120? Thanks!

A: It is questionable. Reason being that the Tapco connection, while it is a 3 pin, may be proprietary ; the phsical sizwe of the connector and the wiring may not matchn the Tapco 120; suggestb buying This power supply specifies the correct voltage, though size and connections of this Mackie power supply my not be compatible. Mackie 402VLZ3, 402VLZ4, 802VLZ3, and 802VLZ3 Ultracompact Mixers Power Connector 2-Pin IEC 250 VAC Device Connector Type 3-Pin Proprietary here is a power supply UPBRIGHT NEW O/P 18.5V x 2 AC Adapter For Tapco MIX. Series MIX.100 MIX.120 MIX100 MIX120 Ultra-Compact Mixer Total Audio Production I/P120V 18W ~ 18V 50/60Hz 15 Watts Power Supply Cord Charger PSU

Q: 8. How do I charge this batter? Do I connect it to a standard home socket? Does it have the cable to connect to a home socket?I have a Evo9.25 that needs 12V 2A input, do I need to buy an extra cable to be able to charge my scope from the battery?

A: the Power Tank comes with an AC charger...Celestron Part #18778, which plugs into the 12V pin. It also comes with a DC connecter, with ends that can plug into a car cigarette lighter, or portable car jump battery, for in field, DC charging.

Q: 9. Is it safe and reliable to run the BMPCC for hours from a wall socket?

A: I had no issues

Q: 10. I live in a country where the outlet voltage is rated at 240V. the rating on this model is 90-140V. Will this model work in my country or do I have to buy a transformer along with it?

A: We do not suggest you use this model internationally; You should purchase the model that comes standard at 240v.