The black SKB iSeries 4909-5 Waterproof Case Foamfrom SKB iSeries 4909-5 Waterproof Case Foamis the solution for storing and transporting your delicate electronics, A/V equipment, microphones, mixers, cables, computers or percussion and music accessories.

The injection molded and waterproof cases are constructed of a high-strength polypropylene copolymer resin, feature a gasket, and are resistant to corrosion, dust, and impact damage. Its molded-in hinges, patented "trigger release" latch system, and automatic ambient pressure equalization valve (MIL-STD-648C) all contribute to its military grade design. The case also features secure stacking, and a comfortable, snap-down rubber over-molded cushion grip handle.

For Storing & Transporting Delicate Gear    Interior 49 x 9 x 5" Dimensions    Injection Molded Case    Layered Foam Interior    Molded-In Hinges    Durable Polypropylene Copolymer Resin    Locking Loops for Optional Padlock    Cushion Grip Handle

Ultra high-strength polypropylene copolymer resin

UV, solvent, corrosion and fungus resistant (MIL-STD-810F)

Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)

Automatic ambient pressure equalization value (MIL-STD-648C & IP67)

Resistant to corrosion and impact damage

Molded-in hinges

Patented "trigger release" latch system

Locking loops to accept a customer supplied lock

Related Questions and Answers

Q: 1. Would a Dell XPS 13 fit in the laptop pocket?

A: When using the SKB iSeries 1309-6 Case with Think Tank Photo Dividers & Lid Organizer, a Dell XPS 13 should fit into the "laptop pocket"

Q: 2. Does this fit the xa40?

A: Yes it does. This case is for the Canon XA40.

Q: 3. Can SKB series 1309 hold Fuji XT-3 with grip and L bracket in vertical position (5.75 inches or 146mm) with foam padding in lid?

A: Hello Walter Unfortunately, the camera will not fit in a Vertical position, only if you were to lay the camera flat.

Q: 4. Will this case hold a Canon 70-200 2.8 IS II lens standing up (vertical), or does it have to lay down (horizontal)?

A: The lens is about 8" long and the dimensions of the case are 20.4 x 11.4 x 7.5", so the lens will fit in two of the dimensions, but not in the third, shortest, dimension.

Q: 5. Just to clarify, will this case hold the C500Mk2?

A: Unfortunately, this case is only for the original Canon EOS C500.

Q: 6. will this work for the c200?

A: Hi Corey, We have not had a chance to check fit of the C200 into this case yet. We should be receiving one directly from Canon soon and will be able to verify at that point. Another couple options that would work if you need to make the move immediately is our 3i-2011-7DZ, 3i-2213-12DL, or 3i-2213-12DT. They all have pull out handle and wheels. The 3i-2011-7DZ is carry on size for airplane travel. It would require you to breakdown the camera similar to the 3i-20118C300 case. The 3i-2213-12DL (with lid organizer) and the 3i-2213-12DT (convoluted foam in the lid) are larger cases and will allow you to leave the top handle on along with other accessories. These three suggested options have high quality inserts that were designed by Think Tank for SKB cases. Thank you,Will

Q: 7. where do you store the top handle?

A: Do you mean the handle for the shoulder rig? If so, I store in the wide space on the right of the case.

Q: 8. TSA Locking latch kit for this particular model?

A: You could use a TSA Lock accessory with the iSeries DSLR Pro Camera case, yes.

Q: 9. Can this case hold D610 with battery drive attached without it pressing hard on the egg crate foam?

A: The D610 is 4.4 tall and the MB-D14 grip adds about 2 so around 6.4 tall. The manufacturer states the case can accommodate 7.5 tall gear. You should be good to go.

Q: 10. will this fit the XA70?

A: Yes, the SKB iSeries Case for Canon XA11/15/40/45/60/65 & Accessories will accommodate the Canon XA70 UHD 4K30 Camcorder with Dual-Pixel Autofocus (B&H # CAXA70).