The CyberPower PR3000LCD Smart App Sinewave UPSfrom CyberPower PR3000LCD Smart App Sinewave UPSprovides backup power essential to keeping your electronics powered should that power be interrupted. This power supply comes equipped with pure sine wave technology ensuring a constant flow of high-quality clean power, while the full automatic voltage regulation feature adjusts the voltage keeping it within a safe operating range to reduce the risk of damage to connected devices. Along with enhanced voltage protection, you can monitor the UPS via the integrated LCD control panel complete with a 4.5' extension cable providing easy access when the UPS is located in hard to reach areas. Once configured, your connected devices are protected up to $375,000 should any of those devices become damaged due to failure of the UPS.

17 min Runtime at Half Load    6 min Runtime at Full Load    8 Hour Typical Recharge Time    Line-Interactive UPS Topology    120 VAC Input Voltage    2700 Output Watts    120 VAC On Battery Voltage    Sine Wave On Battery Waveform    1030 Joules Surge Suppression

Supplies power long enough for equipment to properly shut down when utility power fails. Helps prevent loss of data and minimizes the component stress caused by a hard shutdown.

Diverts excess voltage away from sensitive electronic equipment during an AC power surge or power spike to prevent damage.

Exists when a line interactive UPS has an autotransformer that regulates low voltages (e.g., brownouts) and over voltages (e.g., spikes) without having to switch to battery.

Provides clean, consistent AC power by automatically increasing (boosting) low voltage without using battery power when incoming utility power experiences minor fluctuations.

Provides power protection to ENERGY STAR® 6.0 systems with Active PFC power supplies.

Is a patented design that allows utility power to bypass the UPS transformer, when AC power is stable, which reduces energy consumption, noise, and heat buildup.

Can be removed and relocated for easy viewing using the attached 4.5' cable. This feature provides easy access to view status or change settings on the UPS when it's installed in a hard to reach area such as the bottom of a rack, under a desk, in a crowed IT closet, or on the floor.

Provides IT professionals with tools for monitoring and managing the UPS and backup power. This software offers remote management functionality. Free software download available on CyberPower's site.

CyberPower will repair or replace a defective UPS system (including batteries) within three years of the purchase date. See warranty for details.

Related Questions and Answers

Q: 1. does this make any noise? fan noise? I'm think about mounting this in my sound studio.

A: Bit late to the party, but in the hopes this may help someone: Yes, it makes noise. There is a constant hum, not just when on battery power, and noticeable vibration, kind of like touching a speaker. I would not recommend this for a quiet location.

Q: 2. Does it have a screaming alarm when the power goes out?

A: During a blackout, the CyberPower CP1000PFCLCD PFC Sinewave UPS System has an alarm that will sound—two short beeps, followed by a pause. However, this sound can be muted if needed.

Q: 3. Will this work with Mac OS X, like the CPS1500AVR?

A: I assume you are asking if the UPS software will shut down your MAC if the power fails? You will have to go on line to the units mfg. and read an owners manual. I bought my unit to retain power to my computers if the power failed. When I am doing a video render, I don't want my computer shut down until I am ready. My experience: It performed well during a 3 hour power outage. I would recommend this unit for its intended purpose. Walt Copeland, A/V Engineer

Q: 4. Can you use a 2 Ft. 14 gauge extension cord with the CP 1500PFCLCD? I did use it for several years with a older CP1350PFCLCD. Or is a 2 Ft. 12 gauge extension cord better to use?

A: A 14ga extension cord should be adequate for the wattage capabilities of the CyberPower CP1500PFCLCD PFC Sinewave UPS.

Q: 5. Will this support Windows 10?

A: Yes, it's just a UPS (nothing to do with OS's), you can use it with or without management software.

Q: 6. Does this come with the necessary brackets to use it rack mounted?

A: yes.

Q: 7. This unit is rated at 1000W. Is this based on plugging devices into all receptacles or just the battery and the surge receptacles?

A: That unit is capable of a 1000w peak draw.

Q: 8. Will this be enough for an imac m1 and a lacie d2 hardrive?

A: The BH #CYCP1000PFCL has a 8 minutes at half load rating. Based on the M1 iMacs power draw this should put you in that range of run time.

Q: 9. What is the run time at 50% load?

A: Run time at half load is about 9 minutes.

Q: 10. Am I able to mount this on a 2 post server rack aka telecomm rack? If so, how? What railing system should I use?

A: The CyberPower OR500LCDRM1U Smart App LCD UPS BH #CYOR500LCDRM is compatible with standard racks(1 RU) and mounting hardware is included.