The black Winsted E-SOC Control Station with Monitor Mountsis a workstation that comes with two articulating monitor mounts and features the Versa-Trak monitor mounting system for ergonomic comfort and adjustability. Lift-off access panels, integrated cable management, and a hinged corner make this station a flexible solution suitable for control room applications.

Decorative, vented modesty panel features convenient lift-off panels for easy access to cables, electronics, and CPUs. Integrated cable management with lacing loops keeps cables out of the way.

Hinged corner offers flexibility with no pre-defined corner angles.

Integrated horizontal aluminum track system will support a wide variety of monitor arrays. Versa-Trak offers versatility with easy horizontal adjustment. Post-mounted VESA brackets provide vertical adjustability along with the ability to tilt and pivot the monitors.

Coated with a durable black powder-coat paint that accentuates the work surface. Textured finish prevents fingerprints and lasts for years.

Features a cable channel with lacing hoops incorporated into the modesty panel and a large, drop-down hinged cable tray that spans the length of the modesty panel.

VESA-compliant pivot/tilt mounts easily attach monitors to a support post, and provides smooth pivot and pitch adjustment for optimal viewing of flat panel monitors.

Related Questions and Answers

Q: 1. Is there a good housing for this if we don't want to rack mount it?

A: The product has a sturdy housing, and doesn't necessarily have to be racked.

Q: 2. Does lanc control work with the fx3, if so does touch to focus work?

A: The Sony FX3 Full-Frame Cinema Camera (B&H # SOFX3) does not have a LANC port, which will not allow for control on the Lilliput HT7S 7" On-Camera Control Monitor with LANC Camera Control.

Q: 3. If I were to use this in line with the MX41 as an input to increase inputs to the monitor, would the signal from the mx41b come through ?

A: To begin with, I'm confused with your question, as you refer to an MX41, and an mx41b. Presuming that you mean the Rolls MX41B in both instances, then I am further confused by your question about whether the signal from it would come through. The more clearly you state your question, the better the rest of us can understand and offer help.That being said, there should be no problem to take the output from the MX41B into either the line input or instrument input of the Rolls PM351 and hear all the inputs from both units mixed together on the output of the PM351. It has lots of range and volume available, and is a great, clean headphone amp/mixer/direct box. You will want to pay attention to your stereo and mono cables, as well as the stereo/mono jumpers on the PM351, so you know what you are actually listening to. The MX41B is stereo, so I don't know what happens when you put a mono cable into it... it may only appear on one side of the output. Stereo/mono on the PM351 is selectable with two jumpers. Careful with those jumpers, though, they are black and small and easily lost.The quarter-inches are all unbalanced, too, so don't run those cables more than about 10 feet if you can help it. The XLR's are fine for any length, of course.Hope that helps.rcarbaugh

Q: 4. What preset aspect ratios are available? Is the selected aspect ratio transmitted to the output port or are the aspect ratios simply framing aids?

A: According to Desview, the manufacturer, the Desview U6 5.5 4K HDMI Monitor supports 16:9 and 4:3 aspect ratios. The HDMI out will provide a loop out of the input, bypassing display settings on the monitor.

Q: 5. How long is the duct?

A: The Winsted 42757 Scored Panel Channel Wiring Management Duct is 72" long, 2" wide, and 2" high.

Q: 6. Is this compatible for a7s iii?

A: The Sony a7S iii has a multi port that this cable could connect too. However, the camera is not listed under the compatible cameras. So I can not guarantee this will work with the a7S iii.

Q: 7. Do these knobs come with 6mm or 8mm couplings, or neither?

A: The knobs are the same size that came with the Vixen AP, GP2, and GPD2 Mounts originally.

Q: 8. Are these with 6mm or 8mm couplings, or neither?

A: The Vixen Optics Slow Motion Control Knob for AP, GP2, and GPD2 Mounts is a replacement knob for those mounts. The knobs mount on a shaft that is roughly 6mm in diameter.

Q: 9. Does this unit feature a locking barrel for the DC input?

A: No, the Lilliput HT7S 7" On-Camera Control Monitor with LANC Camera Control does not include a locking barrel power adapter in the box.

Q: 10. can you monitor 4k 60p footage from the camera?

A: The Lilliput HT7S 7" On-Camera Control Monitor with LANC Camera Control can support up to a DCI 4K60p input via HDMI for monitoring.