The black Winsted E-SOC Control Station 72" Black Monitor Mountsis a workstation that comes with four articulating monitor mounts and features the Versa-Trak monitor mounting system for ergonomic comfort and adjustability. Lift-off access panels, integrated cable management, and a hinged corner make this station a flexible solution suitable for control room applications.

Decorative, vented modesty panel features convenient lift-off panels for easy access to cables, electronics, and CPUs. Integrated cable management with lacing loops keeps cables out of the way.

Hinged corner offers flexibility with no pre-defined corner angles.

Integrated horizontal aluminum track system will support a wide variety of monitor arrays. Versa-Trak offers versatility with easy horizontal adjustment. Post-mounted VESA brackets provide vertical adjustability along with the ability to tilt and pivot the monitors.

Coated with a durable black powder-coat paint that accentuates the work surface. Textured finish prevents fingerprints and lasts for years.

Features a cable channel with lacing hoops incorporated into the modesty panel and a large, drop-down hinged cable tray that spans the length of the modesty panel.

VESA-compliant pivot/tilt mounts easily attach monitors to a support post, and provides smooth pivot and pitch adjustment for optimal viewing of flat panel monitors.

Related Questions and Answers

Q: 1. If I were to use this in line with the MX41 as an input to increase inputs to the monitor, would the signal from the mx41b come through ?

A: To begin with, I'm confused with your question, as you refer to an MX41, and an mx41b. Presuming that you mean the Rolls MX41B in both instances, then I am further confused by your question about whether the signal from it would come through. The more clearly you state your question, the better the rest of us can understand and offer help.That being said, there should be no problem to take the output from the MX41B into either the line input or instrument input of the Rolls PM351 and hear all the inputs from both units mixed together on the output of the PM351. It has lots of range and volume available, and is a great, clean headphone amp/mixer/direct box. You will want to pay attention to your stereo and mono cables, as well as the stereo/mono jumpers on the PM351, so you know what you are actually listening to. The MX41B is stereo, so I don't know what happens when you put a mono cable into it... it may only appear on one side of the output. Stereo/mono on the PM351 is selectable with two jumpers. Careful with those jumpers, though, they are black and small and easily lost.The quarter-inches are all unbalanced, too, so don't run those cables more than about 10 feet if you can help it. The XLR's are fine for any length, of course.Hope that helps.rcarbaugh

Q: 2. Can the pm351 pass through phantom power for a mic like SM7B + Cloudlifter?

A: This unit does not provide phantom power.

Q: 3. Do these knobs come with 6mm or 8mm couplings, or neither?

A: The knobs are the same size that came with the Vixen AP, GP2, and GPD2 Mounts originally.

Q: 4. Could I run a stereo signal into this box & send that same stereo out, but allow headphone monitoring of the signal?

A: Yes, this box has a 1/4-inch input that can be switched to stereo, and has a left and right XLR line level outputs, as well as a headphone jack.

Q: 5. Are these with 6mm or 8mm couplings, or neither?

A: The Vixen Optics Slow Motion Control Knob for AP, GP2, and GPD2 Mounts is a replacement knob for those mounts. The knobs mount on a shaft that is roughly 6mm in diameter.

Q: 6. My mixer aux outs are XLR-M, not 1/4". So how do I send the PM351 the monitor output signal? Adapter cable of some sort?

A: If you need to connect a single XLR output from your mixer to the 1/4" TRS input on the Rolls PM351 Personal Monitor Station, you can use a cable like the Hosa Technology HXS-010 Balanced 3-Pin XLR Female to 1/4" TRS Male Audio Cable - 10' (B&H # HOHXS010). If you need to connect both XLR outputs from your mixer to the PM351, simply add on a Y-adapter like the Hosa Technology YXF-101.5 XLR Male to Dual XLR Female Audio Y-Cable (B&H # HOYCXM2XF18).

Q: 7. Will this work for r6 mark ii

A: Yes, the PORTKEYS LH7P 7" High-Bright Touchscreen Monitor with Wireless Control is compatible with the Canon EOS R6 Mark II there just wont be camera control features.

Q: 8. Does it have focus peaking?

A: The PORTKEYS LH7P 7" High-Bright Touchscreen Monitor with Wireless Control (Black) includes focus peaking along with many other tools to assist in shooting.

Q: 9. Will fit Meade lx70 mount?

A: This will not this is dedicated to AP, GP2, and GPD2 Mounts.

Q: 10. How long is the duct?

A: The Winsted 42757 Scored Panel Channel Wiring Management Duct is 72" long, 2" wide, and 2" high.