The blue Canare Male to Right Angle Male HD-SDI Video Cable 6"is a 6" cable that is hand-assembled with Canare extra flexible L-5CFW HD-SDI RG6 coaxial cable, and Canare true 75-ohm HD BNC connectors. This cable is 100% sweep tested to conform to SMPTE 259M, 292M, 424M, 2081-1, and 2082-1 standards. The combination of Canare BNC connectors used in this series exceed 3.0Gb/s HD-SDI requirements specified in SMPTE 424M and are fully rated for extended distances for 3G-SDI ST424 out to 340 Feet.

18 AWG RG6 SDI Coaxial Cable    BNC Male to Right Angle Male Connectors    Solid Copper Center Conductor    Foam PE Dielectric Insulation    Dual Copper Braid    100% Sweep Tested

Hand made with Canare L-5CFW 18AWG stranded center conductor, 75-ohm Precision HD-Serial Digital Video Coax cable for professional broadcast performance

Cables meet SMPTE 259M, 292M,3G 3G 424M, 6G 2081-1, 12G 2082-1 Standards

Canare BCP-B51F straight, and BCP-LC5F right angle, true 75-Ohm BNC connectors, exceed 6.0Gbps HD-SDI SMPTE requirements

Dual copper braid for flexibility and bending performance

100% sweep tested

Related Questions and Answers

Q: 1. will this work with Blackmagic 7" 12g video assist monitor?

A: No, the IndiPRO Tools D-Tap to Locking 2.1mm DC Right-Angle Cable (24") is not the correct size barrel, as the Blackmagic Design Video Assist 7" 12G-SDI/HDMI HDR Recording Monitor has a 5.5 x 2.5mm DC input. You can use the DigitalFoto Solution Limited D-Tap to 5.5 x 2.5mm DC Barrel Power Cable (36.4") instead. See: https://bhpho.to/2OYfRCg

Q: 2. Would this cable work with connecting an UltraSync One to a bmpcc 6k? Then, to confirm, I would need another UltraSync One connected to a Zoom F8n, which would utilize the BNC to Atomos LTC? Thanks in advance.

A: Yes, the Atomos LTC to Right-Angle 3.5mm Mic-Level Timecode Cable will work to connect an UltraSync One to a BMPCC to send timecode, then you can use a cable like the Atomos DIN to BNC Timecode and Genlock Cable for UltraSync ONE (B&H # ATOMXCAB01) for the Zoom F8n. Once the UltraSync One is synced with the device, timecode is embedded in the recorded files and can be recognized by industry-standard software and NLEs (non-linear editors).

Q: 3. Will this adapter fit on a 5/8" light stand? Will the opening in the bottom fit over a light stand stud? Is that a threaded hole at the bottom side that I can attach a knob?

A: This adapter would not fit over a 5/8" stud on a light stand. A better option for this is the Avenger E390 TVMP Yoke to Stand Adapter, BH # AVE390. http://bhpho.to/3mKtX5z

Q: 4. Would this work with smallhd Indie 7 locking barrel?

A: Smallhd recommends using their D-Tap to 5.5mm Male DC Barrel Power Cable (3') for use with the Smallhd Indie 7. https://www.bhphotovideo.com/c/product/1154925-REG/smallhd_cbl_pwr_dtap_bar_36_d_tap_adapter_cable.html/qa

Q: 5. What are the dimensions of the right angle connector?

A: Approximately 1'' x .5''.

Q: 6. will it work with core edge v mount battery?

A: This is not compatible with that battery.

Q: 7. Does this regulate to 12 volts?

A: This does not regulate power. You use it with devices that self regulate.

Q: 8. Would this work to split two wireless transmitters into two separate channels recorded onto a tascam dr-70d?

A: The RODE SC11 Right-Angle 3.5mm TRS Y-Splitter Cable can split the audio from the 3.5mm output on a dual-channel wireless receiver and send the audio to two 3.5mm audio inputs, but the TASCAM DR-70D Multitrack Field Recorder has only one 3.5mm input and four XLR-1/4" combo-jack inputs. As a better option, you can use a 3.5mm to dual XLR male cable like the Cable Techniques 3.5mm Right-Angle TRS to Dual Low-Profile 3-Pin XLR Male Y Cable - 15" (B&H # CATGO2YX3M15) or the Hosa Technology Pro Stereo Breakout Cable - 3.5mm Stereo Mini to Dual 3-Pin XLR Male - 3' (B&H # HOHMX003Y).

Q: 9. Can this be used to send signal from 1 microphone (like Rode VideoMicro) to 2 recorders (like Zoom F1)? If yes - then how the recorders' "plug-in power" should be set? 1 On, 1 Off? Both On? Does it matter?

A: I would not expect that plug in power will work at at all.

Q: 10. Tilta TA-BTP-F970 NP-F970 Battery Plate

A: It is compatible.