The blue Canare Male to Right Angle Male HD-SDI Video Cable 35ftis a 35' cable that is hand-assembled with Canare extra flexible L-5CFW HD-SDI RG6 coaxial cable, and Canare true 75-ohm HD BNC connectors. This cable is 100% sweep tested to conform to SMPTE 259M, 292M, 424M, 2081-1, and 2082-1 standards. The combination of Canare BNC connectors used in this series exceed 3.0Gb/s HD-SDI requirements specified in SMPTE 424M and are fully rated for extended distances for 3G-SDI ST424 out to 340 Feet.

18 AWG RG6 SDI Coaxial Cable    BNC Male to Right Angle Male Connectors    Solid Copper Center Conductor    Foam PE Dielectric Insulation    Dual Copper Braid    100% Sweep Tested

Hand made with Canare L-5CFW 18AWG stranded center conductor, 75-ohm Precision HD-Serial Digital Video Coax cable for professional broadcast performance

Cables meet SMPTE 259M, 292M,3G 3G 424M, 6G 2081-1, 12G 2082-1 Standards

Canare BCP-B51F straight, and BCP-LC5F right angle, true 75-Ohm BNC connectors, exceed 6.0Gbps HD-SDI SMPTE requirements

Dual copper braid for flexibility and bending performance

100% sweep tested

Related Questions and Answers

Q: 1. Can this be used to send signal from 1 microphone (like Rode VideoMicro) to 2 recorders (like Zoom F1)? If yes - then how the recorders' "plug-in power" should be set? 1 On, 1 Off? Both On? Does it matter?

A: I would not expect that plug in power will work at at all.

Q: 2. Will this work connected to 2 Rode receivers (so I want to record 4 transmitters), to my Sony A7R5, (4 channels of audio)?

A: The RODE SC11 Right-Angle 3.5mm TRS Y-Splitter Cable is designed for connecting the mono outputs of two devices and sending it to separate channels on a device with a single 3.5mm TRS mic input. The SC11 will carry only two channels of audio. It can be used to connect the mono (combined) output signal from two dual-channel wireless receivers, like the RODE Wireless GO II Microphone System, to the mic input on a camera such as the Sony a7R V Mirrorless Camera. The audio carried by the cable will have the combined audio from one system on the left side and the combined audio the second system on the right side.

Q: 3. Can this be used with the Blind Spot Power Junkie?

A: Not that we are aware of. This connection is for Tilta products. For the Blind Spot Power Junkie we can suggest BH #BLBSG1302901 instead, which is the Canon LP-E6 dummy battery option. This will work to power the Pocket Cinema Camera 4K from the Blind Spot Power Junkie. https://bhpho.to/39hdCyS

Q: 4. Will this work with Tilta's side power handles?

A: The Tilta 2.5mm DC Male Barrel Power Cable will not work with the Tilta Side Power Handles as it does not have an barrel port for powering, only USB for the Nucleus motors.

Q: 5. Can I use this to connect an Atomos AtomX Sony L-Series Type Battery Eliminator on an Atomos Ninja V to a V mount setup?

A: No, barrel will not fit its a 5.5/2.5 mm dc cable.

Q: 6. Will this work with the Dji RS2?

A: The DJI RS2 does not have a 2-pin LEMO port, nor a DC port.

Q: 7. Would this work with smallhd Indie 7 locking barrel?

A: Smallhd recommends using their D-Tap to 5.5mm Male DC Barrel Power Cable (3') for use with the Smallhd Indie 7. https://www.bhphotovideo.com/c/product/1154925-REG/smallhd_cbl_pwr_dtap_bar_36_d_tap_adapter_cable.html/qa

Q: 8. Can it work with any timecode box?

A: The Tentacle Sync C07 Tentacle to DSLR 3.5mm Mini-Jack Cable is designed to send timecode from a Tentacle Sync timecode generator to any DSLR camera or recorder that includes a 3.5mm TRS input jack. This cable should also work with other timecode generators that use a 3.5mm TRS timecode output connection to send timecode to a camera or recorder that has a 3.5mm TRS input.

Q: 9. will this work with Nikon D500?

A: Yes, the TetherPro USB 3.0 to Micro-B cable, is the correct cable for a Nikon D500.

Q: 10. Would this cable work with connecting an UltraSync One to a bmpcc 6k? Then, to confirm, I would need another UltraSync One connected to a Zoom F8n, which would utilize the BNC to Atomos LTC? Thanks in advance.

A: Yes, the Atomos LTC to Right-Angle 3.5mm Mic-Level Timecode Cable will work to connect an UltraSync One to a BMPCC to send timecode, then you can use a cable like the Atomos DIN to BNC Timecode and Genlock Cable for UltraSync ONE (B&H # ATOMXCAB01) for the Zoom F8n. Once the UltraSync One is synced with the device, timecode is embedded in the recorded files and can be recognized by industry-standard software and NLEs (non-linear editors).