The white Da-Lite 20325E 45x80 Tensioned Advantage Deluxe Screenfrom Da-Lite 20325E 45x80 Tensioned Advantage Deluxe Screenis designed to be concealed neatly in a ceiling when not in use, which makes it ideal for corporate conference rooms. The screen can be installed in two stages; the screen case can be installed during construction, and the screen assembly can be attached during the finishing stage. Once the screen is installed, the screen's trim conceals the rough opening in the ceiling, eliminating the need to complete additional trim work. Sliding installation brackets allow you to attach the screen housing to the structure above the drop ceiling. Closure doors keep the screen out of sight when it isn't being used.

The HD Progressive 1.1 Perf surface has a 1.1 gain, 170° viewing angle, and is ideal for applications where projector brightness and screen size require an increase in gain. The white surface offers true color reproduction and fidelity. The perforated vinyl surface allows for the installation of speakers behind the surface. HD Progressive 1.1 Perf can be cleaned with mild soap and water, and is flame-retardant and mildew-resistant. It is also GREENGUARD GOLD Certified. Each side of the material uses a tab guide cable system to maintain even lateral tension and hold the surface flat. This helps to ensure that pixels from the display image don't overlap with one another. Tensioning also helps to prevent creases or folding of your screen. A custom slat bar with added weight maintains vertical tension on the screen surface.

For controlling the screen, a three-position Decora-style wall plate is included, along with a cover switch. Low Voltage Control allows the screen to be controlled via a low voltage signal or momentary dry contact from a third-party control system. The LVC is necessary if you are using an IR or RF remote to control your screen.

92" Diagonal    16:9 Aspect Ratio    HD Progressive 1.1 Perf Surface    1.1 Gain, 170° Viewing Angle    Black Backing on Surface    Tensioned for Flat Image Display    220-240VAC, 50Hz Motor    Three-Button Decora-Style Wall Switch

The screen has two motors, both mounted inside the case. One motor operates the door at the bottom of the case, and the other controls the viewing surface.

The electrical junction box is internally integrated into the housing, making it possible to install the housing, and then wire to the building's electrical system during construction.

Smooth Roll Technology to keep your screen flat.

Slim-Tab, a lower profile, and strong tab design to keep your screen taut.

White powder-coated case with white endcaps and closure doors for a clean aesthetic.

The case is UL Plenum rated.

Related Questions and Answers

Q: 1. Will this work with a Sony PXW-Z280?

A: Yes it should. The PXW-Z280 has a LANC input for a controller, which is the kind of connection this product has. They should work well together.

Q: 2. How do you keep the modeling lamp on. As soon as I take a photo, the modeling lamp goes off. I'm using the Elinchrom EL19366 Skyport Transmitter?

A: Hi,If you check your instruction book you will see how to control the modeling lamp.Here is the item you are inquiring about.Setup Visual-Flash-Control (VFC) modeProportional modelling lamp setup (PMS) Enter VFC setup :1. Press Prop push button for more than 2 seconds, until the display shows F.X (X is 0 or 1) toenter into the Modelling lamp setup menu.2. Use the Flash-Power up and down button to change setting:- F.0: Visual-Flash-Control = OFF. Modelling lamp remains ON after flash.- F.1: Visual-Flash-Control = ON. Modelling lamp switches off during recharging.3. The display switches back to normal mode after approx. 4 seconds if no button is pressed. Thesettings are automatically stored.4. Standard setting is F.0, VFC = OFFI hope this helps.Regards,Will H

Q: 3. Will this allow for start/stop trigger via CN18-80mm and Canon C100 II?

A: The VariZoom VZPGC Deluxe Zoom Controller is designed specifically for the Canon CN-E 18-80mm & 70-200mm Lenses and Cano's professional camcorders so, yes, the red button can be used for start/stop record.

Q: 4. Will this work on the CN17x17 Cine Servo Lens?

A: It will not. This product is for the Canon CN-E 18-80mm and 70-200mm Lenses only.

Q: 5. will this work with the JVC GY-HM600U?

A: Yes, this will work with the JVC GY-HM600U using the 2.5 mm remote port.

Q: 6. will this work with the canon xa30 camcorders

A: Yes, this LANC controller should work with the Canon XA30. The XA30 has a standard Canon LANC input.

Q: 7. how far does the arm extend?

A: Using the included aluminum shafts it can extend 2 , 4 or 6 .

Q: 8. Would this Zoom control be able to work with Zacuto Z-CNYC Y-cable and the canon FPD-400D?

A: It will not. This is specifically for the Canon CN-E 18-80mm & 70-200mm Lenses.

Q: 9. Is this controller ambidextrous?

A: As my father was a south-paw, I understand your concern. While we have not tested it, we would say that you should have no real issues using this on the left pan handle. The record button may be a bit of a stretch for your left thumb but other than that, you should be fine.

Q: 10. can extensions be added to this arm for example if we need to to be 18 inches instead of 9 ? I am looking for a wall mount that can be swung out of the way for a small camera so when we use the camera we will swing it out when we are not using the camera it can be stored against the wall

A: Yes, I have ordered many of these units and mixed and matched the poles to make several mounts of varying sizes. Each pole extension uses the same 1/4 -20 screw size, so even the camera could mount directly to the pole rather than the ball mount.