The white Da-Lite 20325I 45x80 Tensioned Advantage Deluxe Screenfrom Da-Lite 20325I 45x80 Tensioned Advantage Deluxe Screenis designed to be concealed neatly in a ceiling when not in use, which makes it ideal for corporate conference rooms. The screen can be installed in two stages; the screen case can be installed during construction, and the screen assembly can be attached during the finishing stage. Once the screen is installed, the screen's trim conceals the rough opening in the ceiling, eliminating the need to complete additional trim work. Sliding installation brackets allow you to attach the screen housing to the structure above the drop ceiling. Closure doors keep the screen out of sight when it isn't being used.

The HD Progressive 1.1 Perf surface has a 1.1 gain, 170° viewing angle, and is ideal for applications where projector brightness and screen size require an increase in gain. The white surface offers true color reproduction and fidelity. The perforated vinyl surface allows for the installation of speakers behind the surface. HD Progressive 1.1 Perf can be cleaned with mild soap and water, and is flame-retardant and mildew-resistant. It is also GREENGUARD GOLD Certified. Each side of the material uses a tab guide cable system to maintain even lateral tension and hold the surface flat. This helps to ensure that pixels from the display image don't overlap with one another. Tensioning also helps to prevent creases or folding of your screen. A custom slat bar with added weight maintains vertical tension on the screen surface.

For controlling the screen, a three-position Decora-style wall plate is included, along with a cover switch. Low Voltage Control allows the screen to be controlled via a low voltage signal or momentary dry contact from a third-party control system. The LVC is necessary if you are using an IR or RF remote to control your screen. The video projector interface provides DC controls that allow you to control the screen by simply turning your projector on or off. The screen will descend when the projector is turned on, and retract back into the case when the projector is turned off. Your projector must have a 12V or 5V lead to operate the interface (cable not included).

92" Diagonal    16:9 Aspect Ratio    HD Progressive 1.1 Perf Surface    1.1 Gain, 170° Viewing Angle    Black Backing on Surface    Tensioned for Flat Image Display    110-120 VAC, 60 Hz Motor    Three-Button Decora-Style Wall Switch    Includes Control Through Projector

The screen has two motors, both mounted inside the case. One motor operates the door at the bottom of the case, and the other controls the viewing surface.

The electrical junction box is internally integrated into the housing, making it possible to install the housing, and then wire to the building's electrical system during construction.

Smooth Roll Technology to keep your screen flat.

Slim-Tab, a lower profile, and strong tab design to keep your screen taut.

White powder-coated case with white endcaps and closure doors for a clean aesthetic.

The case is UL Plenum rated.

Related Questions and Answers

Q: 1. Are all of the screws and sockets on all parts 1/4-20?

A: Yes they are

Q: 2. Bought a new Canon XF-705. Will this function well with this? Any ideas for other controllers? We tried the Manfrotto arm controller and an older Canon and all were wonky and not reliable with it. Thanks!

A: The XF705 has a LANC input, this controller should work well with it.

Q: 3. Does this zoom controller work with the Canon CN-E 18-80mm lens?

A: Yes, the VariZoom VZPGC20 20-Pin Zoom Control for Canon CN-E 18-80mm & 70-200mm Lenses is compatible with the Canon CN-E 18-80mm lens.

Q: 4. How do you keep the modeling lamp on. As soon as I take a photo, the modeling lamp goes off. I'm using the Elinchrom EL19366 Skyport Transmitter?

A: Hi,If you check your instruction book you will see how to control the modeling lamp.Here is the item you are inquiring about.Setup Visual-Flash-Control (VFC) modeProportional modelling lamp setup (PMS) Enter VFC setup :1. Press Prop push button for more than 2 seconds, until the display shows F.X (X is 0 or 1) toenter into the Modelling lamp setup menu.2. Use the Flash-Power up and down button to change setting:- F.0: Visual-Flash-Control = OFF. Modelling lamp remains ON after flash.- F.1: Visual-Flash-Control = ON. Modelling lamp switches off during recharging.3. The display switches back to normal mode after approx. 4 seconds if no button is pressed. Thesettings are automatically stored.4. Standard setting is F.0, VFC = OFFI hope this helps.Regards,Will H

Q: 5. how far does the arm extend?

A: Using the included aluminum shafts it can extend 2 , 4 or 6 .

Q: 6. Is this controller ambidextrous?

A: As my father was a south-paw, I understand your concern. While we have not tested it, we would say that you should have no real issues using this on the left pan handle. The record button may be a bit of a stretch for your left thumb but other than that, you should be fine.

Q: 7. Does this come with the clamper to put on a tripod arm?

A: Yes, the clamp is included.

Q: 8. will this work with the canon xa30 camcorders

A: Yes, this LANC controller should work with the Canon XA30. The XA30 has a standard Canon LANC input.

Q: 9. Will this work with a Panasonic HC-X1000?

A: This controller is for Sony and Canon LANC compatible cameras. It will not work with the HC-X1000, however we do have some Panasonic compatible controllers that will work. B&H # VAVZPROPZFI is the Panasonic version of this controller and is a good fit for the HC-X1000.

Q: 10. Will this work with a Sony PXW-Z280?

A: Yes it should. The PXW-Z280 has a LANC input for a controller, which is the kind of connection this product has. They should work well together.