[Yes] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projection screen/case up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem!

[Yes] I love this product, Easy to install and and look even better on the wall.

[HD Pro 1.1 Perf] great - for a case, not a very hard job. still done well.

[170 degrees] Looking forward to getting all of this stuff together

[16:9] We use the electrol screens almost exclusively in close to a 100 locations. They are versatile and durable.

[120 x 13 x 10"] This Screen was easy to install. It took 3 people and 2 ladders to get the job done. The remote is really not needed but i opted to install it as well. The motor runs really smooth. The screen is nice and wide. A really good buy.

[Yes] Having been around Electronics / State and Event production for nearly 50 years I learned a long time ago the importance of having cases for all portable equipment. So when I ordered my first 100 Da-Lite Insta Theater screen I also order this case. Over the last 2 years we provided services for about 50 events and this case has held up great! No tears and resists scuffs very well. But what is more important is that it does as great a job protecting the black anodized aluminum screen cover - which, without a case - would be trashed very quickly. When I order a 2nd 100 screen last month you can bet that I also ordered the case to go with it!

[75 lb] I installed in my living room in between ceiling joists. It works great. I use it with a Panasonic HD projector. It impresses everyone who walks in the room. Has a clean appearance when retracted. Note: it didn't come with a 12v trigger as both the B&H customer service rep and myself thought it did. We both misunderstood the description (it's optional.) The part was available at Da-Lite for $80 and came with no instructions. I got it to work after a few emails and chats with da-lite. Also, I ended up placing some holes in the top of the case to mount using 8 Lag bolts into the 2nd story floor structure. All the hardware that comes with it assumes you will have access to hang it from the top which requires access via the side while it's in it's final position. I was putting it in a hole the size of the case in my finished ceiling so that method would not work ( I would have had to remove and re-install a lot of drywall). I knew this before I purchased by reading the installation instructions so no worries just a fact and maybe a consideration for future changes to the case or just the directions.

[170 degrees] We use the screen in our church sanctuary once or twice a month. Installing it was an adventure with the weight and length, but several sections of scaffolding and a couple friends made the install move along nicely. The instructions for wiring were right on and it worked first try! The image is right on and visible the entire length of our viewing area (over 100').

[Yes] This screen was installed in a small conference room with an NEC projector. The screen can be wall or ceiling mounted, and this flexibility came in handy when we had to switch to a ceiling mount at the last moment. The screen presents very well, and is unobtrusive when retracted. The tensioning system works nicely, and we didn't have to change any of the factory settings for the drop. I would have liked to see some additional mounting holes for attaching the screen to studs in the wall, so the installer has more options for wall mounting.