The Da-Lite 24418 60x96 UTB Contour Fixed Frame Screenhas an ultra-thin bezel and acid etched black aluminum frame for keeping the audience's focus on projected content. The Da-Mat surface has a 1.0 gain and 120° viewing angle, with black backing to prevent bleed-through and retain brightness. Its low-profile flat-panel design allows it to sit 1.38" off the wall. The front lip of the bezel is .25" wide all around the viewing surface, which sits .13" off of the inner frame component.

Da-Mat is a unity gain vinyl surface. It features a white seamless surface for good color reproduction for environments with controllable ambient light. The screen comes with reinforced black binding on all four sides. The surface wraps around the frame and attaches to it with metal grommets. The Da-Mat surface can be cleaned with mild soap and water, and is flame-retardant and mildew-resistant. It is also GREENGUARD GOLD Certified.

113" Diagonal    16:10 Wide Format    Ultra-Thin Bezel Frame    Acid Etched Black Frame    Da-Mat Surface    1.0 Gain & 120° Viewing Angle    Black Backing Retains Brightness

Related Questions and Answers

Q: 1. Does this have the standard Elinchrome mount-will fit any Elinchrome speedrings, reflectors, etc?

A: Yes standard Elinchrome EL mount

Q: 2. Is there anywhere I can purchase a replacement stand socket?

A: A replacement stand socket can be purchased through Elinchrom directly. Please use the following for access to their parts and service page: http://bit.ly/1H3eFhi

Q: 3. Can this be triggered by pocket wizard?

A: Only if a PocketWizard is attached to it; it does not have a built-in PW receiver.

Q: 4. what's the best white balance for Elinchrom D-Lite 400W/s RX 4 Flash Head ?

A: Hi,Your best bet is to do a custom white balance in your camera. If you wish not to perform that function than set the white balance to the flash symbol.Regards,Will HBrand Manager Lighting, MAC Group US

Q: 5. Will this fit on the old Ezybox speedlite as well?

A: There was a substantial design change between the two models.

Q: 6. Will this work with a canon eos 250d? Even the hot shoe included?

A: Yes, the Elinchrom Skyport transmitter included with the Elinchrom D-Lite RX 4/4 Softbox to Go Kit would be compatible with DSLR cameras such as the Canon EOS 250D.

Q: 7. Hi dear B&H friends. It comes for Sony Multi Interface Shoe, ie. A7, A7II, A7III, A60...? -Sergio- from PR

A: The Odin Lite is a Manual trigger. You can use it on any camera system including Sony.

Q: 8. How do you keep the modeling lamp on. As soon as I take a photo, the modeling lamp goes off. I'm using the Elinchrom EL19366 Skyport Transmitter?

A: Hi,If you check your instruction book you will see how to control the modeling lamp.Here is the item you are inquiring about.Setup Visual-Flash-Control (VFC) modeProportional modelling lamp setup (PMS) Enter VFC setup :1. Press Prop push button for more than 2 seconds, until the display shows F.X (X is 0 or 1) toenter into the Modelling lamp setup menu.2. Use the Flash-Power up and down button to change setting:- F.0: Visual-Flash-Control = OFF. Modelling lamp remains ON after flash.- F.1: Visual-Flash-Control = ON. Modelling lamp switches off during recharging.3. The display switches back to normal mode after approx. 4 seconds if no button is pressed. Thesettings are automatically stored.4. Standard setting is F.0, VFC = OFFI hope this helps.Regards,Will H

Q: 9. What is the part # for the reflector that will fit the D-Lite 400W/s RX 4? I see that it does not come with one.

A: ELR6 is the umbrella reflector https://bhpho.to/2K0SfIe.

Q: 10. Is the motor compatible with the SmallRig Wireless Follow Focus Contro? https://www.bhphotovideo.com/c/product/1730054-REG/small

A: Yes, the SmallRig Wireless Follow Focus Lite Kit included focus motor is compatible with the SmallRig Wireless Follow Focus Controller Kit (BH #SM3917).