The silver Global Truss Jr. Snap Clamp - Medium-Duty Silver Truss Clampfrom Global Truss Jr. Snap Clamp - Medium-Duty Silver Truss Clampis a medium-duty, hook-style wraparound clamp with snap-on functionality. This solid metal clamp is compatible with F23 and F24 truss sections, it has a load capacity up to 165 lb, and features an M10 threaded stud base connector.

Wrap Around Hook Style Clamp    Load Capacity: 165 lb    For F23 and F24 Trusses    M10 Threaded Stud Base

Related Questions and Answers

Q: 1. Will it clamp to a 21" iMac?

A: The Satechi 6-in-1 USB Type-C Hub Clamp for 24" iMac (Silver) BH #SASTUCICHS is specifically for the 2021 24" iMac.

Q: 2. Does it mount onto Impact Light Stand, Black (6') B&H # IMLS6B MFR # LS-6B?

A: This clamp can attach to an Impact 6' Light stand either using the 5/8 female slot with the included stud removed on the clamp or it can bit the tubing of the stand in a horizontal position.

Q: 3. Will this mate with a Manfrotto superclamp? Are they essentially identical in design? (I want to connect two superclamps together and I already own one superclamp.)

A: Yes this will work.

Q: 4. I see that the accessory attachment point is 1/4-20. Would it be OK to drill and tap this bigger to 3/8-16 to accommodate my new Matthews magic arm? I don't want to ruin the structural integrity of the clamp.

A: You can purchase Manfrotto 036-38 Standard Stud with 3/8" Screw B&H # MA03638 replacement stud.

Q: 5. is the ratchet handle a true ratchet? or is it the same as Manfrotto's that will block you from turning the handle if you are in a tight place.

A: It is the same as Manfrottos. It is not a true ratchet. It must be pulled outward about 0.25 inches, but then it can be turned freely to any position. Just like Manfrottos, once it is in a new position it can be turned tighter or looser as needed. It requires very little room to tighten, pull out, rotate counter clockwise, push in, then tighten a little more, repeat as needed. Or loosen, pull out, rotate clockwise, push in, then loosen a little more, repeat as needed.

Q: 6. What is the depth of the two M5 threaded holes? (So I can purchase the right M5 bolt length) Thanks in advance.

A: The M5 threaded holes are 15mm deep.

Q: 7. Can this hold a t8 bulb? How small can this clamp down?

A: The Matthews Super Mafer Clamp with Baby (5/8 ) Pin has a maximum jaw opening of 2 inches, while the diameter of a T8 fluorescent bulb is 1 inch. As such, yes, a Matthews Super Mafer Clamp with Baby (5/8 ) Pin may hold a T8 fluorescent bulb. I would simply caution its usage as the glass bulb is fragile and the clamp is strong and can easily crush the bulb.

Q: 8. What's a good articulating arm for this ?

A: The choice of arm would depend on the item you wish to attach, the reach and level of adjustment you need when attaching to the Impact Super Clamp with Ratchet Handle BH #IMCC106R.

Q: 9. will this lock tightly on a 15 mm width flat stock?

A: Yes, this should attach tightly to something that is 15mm wide.

Q: 10. I have a Sirui K20X ballhead, how could I attach to this clamp?

A: As long as your ballhead is equipped with 5/8 or 1/4 threaded insert at the bottom, is just a matter of thread in baby stud into it and than secure ballhead into a clamp with provided wing screw. After that ready to use