The RAM-A-CAN II Cup Holder Mount with X-Grip III Holderfrom RAM-A-CAN II Cup Holder Mount with X-Grip III Holderis designed with a 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm, allowing for unlimited viewing angles. It consists of the RAM-A-CAN II cup holder base, a double socket arm, and universal X-Grip III cradle.

Rubber Ball and Socket System    Adjustment Points at Ends of Arm    Compatible with Most 10" Tablets

The RAM X-Grip III cradle is compatible with the following tablets with or without the case:

Apple iPad Air, Apple iPad 4 (with Lightning Connector), Apple iPad 3, Apple iPad 2, Apple iPad 1, HP TouchPad, Asus Eee Pad, Asus Eee Pad Transformer, Lenovo LePad Slate and IdeaTab Lynx, LG G-Slate, LG Optimus Pad, Microsoft Surface, Motorola XOOM, Motorola XYBOARD 10.1,

Samsung Galaxy Tab 8.9, Samsung Galaxy Tab 10.1 2014 Edition, Samsung Galaxy Tab 10.1, Samsung Galaxy Tab 2 10.1, Samsung Galaxy Tab 3 10.1, Toshiba Thrive, and most 10" screen tablets

Related Questions and Answers

Q: 1. is there anything at the very tip of the boom? Like a 1/4 20 or 5/8? Or can you attach a light stand spigot so you can attach other pieces of equipment?

A: I threaded the end with an inexpensive 3/8 -16 hex die, which only requires a wrench to turn it to cut the threads. The post is just a hair too small in diameter for a true 3/8 thread, but it holds onto a 3/8 mic attachment just fine.

Q: 2. Hi!! Will this fit in Manfrotto 5002BL Nano Plus Stand (6.5')?

A: yes. just would suggest a sandbag to weigh down the unit so it stays in place.

Q: 3. Does this case have an attachment hole for a lanyard or mini ‘biner?

A: Unfortunately, the PolarPro Slate CFEB Edition II Memory Card Holder (Forest) does not have an attachment hole for a lanyard or carabiner.

Q: 4. Will this hold a Profoto 33" collapsible reflector??

A: Yes, the Avenger RH353 Reflector Holder with Mini Grip Head, B&H # AVRH353, listed above will hold the Profoto Collapsible Reflector 33".

Q: 5. Can I use the Avenger RH353 Reflector Holder with a Manfrotto 5001B?

A: I use my RH353 with a Manfrotto 5001BAC...had some difficulty attaching the clamp to the top section of the light stand, as the diameter of the light stand pole seemed a bit too large for the RH353's clamp. Ultimately got it to work, though. Used indoors only with a 40 collapsible reflector attached with the holder at approx. 90 degrees to the light stand, and the whole rig was very stable. BobH

Q: 6. How wide do the clips open? I have some triangular manfrotto reflectors that have quite thick frames. Thank you.

A: Approximately one inch

Q: 7. Does this fit on d1?

A: Profoto OCF modifiers are not designed to be used on D series flashes.

Q: 8. Will this work on the minimax?

A: The following Easyrig Umbrella with Holder is for the MiniMax. Easyrig Umbrella with Holder for Minimax BH #EAERIGMM055

Q: 9. How to place an AirTag in this holder. I can’t seem to unscrew the item to place the AirTag in the holder. Any ideas?

A: With the Nanuk Airtag Holder, you have to slide out the plastic cover and you will see two screws. You have to use a Philips screw driver remove the screws and place the Airtag in the compartment. You can find a step by step guide in the instruction booklet the item comes with.

Q: 10. Does the grid holder fit the original grids?

A: The OCF ll Grids are secured in the Grid and Gel Holder by magnets. The original OCF Grids are not magnetic, and therefore may no fit securely.