The white RS-EZ Series RS62-EZ 6.5" Coaxial Speaker Open-Ceiling Hanging Speaker from SoundTube Entertainment is designed for open-ceiling applications and features a 6.5" coaxial driver with BroadBeam Ring technology for consistently smooth high-frequency directivity. It incorporates a 4-position ceramic terminal block input connector and a 6-position tap switch with transformer bypass position. This speaker comes with hanging hardware that includes galvanized steel cables and a built-in hanging bracket for fast, easy, and secure installation. The unit may be mounted direct-to-conduit via the included screw-on locking cover plate (included).

The speaker enclosure is constructed of injection-molded ABS with glass fiber reinforcement for durability in indoor or outdoor applications. It also features an aluminum grille with protective powder-coated finish. The speaker offers an impedance of up to 16Ω for easy daisy chaining in low voltage systems. The ceramic input terminal accepts up to 10-gauge plenum-rated signal wire and includes a thermal fuse. The RS62-EZ speaker includes hanging cables and a built-in mounting plate for suspending it; a threaded opening on top of its cover plate allows for direct-to-conduit mounting. This speaker is suitable for use in voice alarm applications subject to EU EN60849 and BS5839-8 regulations. It is suitable for installation in retail, grocery stores, restaurants, hotels, casinos, museums, trade shows, and conference rooms.

Features a 6.5" (165mm) coaxial driver with BroadBeam Ring technology for consistently smooth high-frequency directivity

Weatherized components for indoor and outdoor applications

Includes hanging hardware with galvanized steel cables and hanging bracket for fast, easy, and secure installation

Unit may be hung using the included mounting hardware or mounted direct-to-conduit via locking cover plate (included)

Enclosure constructed of injection molded ABS with glass fiber reinforcement for durability

16Ω impedance for easy daisy chaining in low voltage systems

Aluminum grille with protective powder-coated finish

Built-in thermal fuse

UL 1480 UEAY planned, UL 2239 approved

Related Questions and Answers

Q: 1. At 3.3 pounds, how sturdy is the stand, really?

A: The stand is suitable for holding up the background in the kit. It is not suitable for a large light.

Q: 2. What is the minimum height the stand will support the pop-up background when mounted horizontally?I need something that can adjust down to about 36 horizontally.

A: The stand can easily be below 36 inches as I carry it in a 35 inch hard case and can be set up to be about 36 to 37 inches. HOWEVER, your popup is 5 feet by 6 1/2 feet. So even with the stand low, the pop will be too tall by over 2 feet when place in the landscape (horizontally) position. I'm not sure of your end use, but as you described your need, stand yes, but the popup no.

Q: 3. Is there an easy way or a certain way to fold this up? I love the backdrop but can't get it back in the bag.

A: Please refer to the following instructional video for reference. https://bit.ly/2PPIb4v

Q: 4. Can this backdrop also be used for self taping?

A: You can certainly use this background for self-taping.

Q: 5. Can this be use horizontally (i.e. 7' wide)?

A: Yes.

Q: 6. This product advertises a reversible Blue/Gray screen, I'm searching for a green screen, can I get the same result with either color?

A: No, only with the blue side. The grey is not for chroma key, just standard shooting.

Q: 7. How wrinkled is the background right out of the box? Does it need to be steamed before use?

A: The cloth background has the potential to wrinkle but the metal band helps pull it out. In most cases you do not need to steam it.

Q: 8. how do you hang it horizontally with the included stand?

A: There are touch-fastener for both vertical and horizontal use on the light stand and there are loops on the side of the green screen that will allow for mounting both ways.

Q: 9. I’m having trouble connecting the backdrop to the stand when hanging horizontally. When horizontal, there are no straps in the middle to connect to the stand, so how can it effectively connect and hang centered when there are no straps in the middle, only on either side of the middle? Thanks for your help!

A: This stand is made for Vertical orientation. You can use a 2nd stand for horizontal or get this stand with 2 clips B&H # IMLSRH

Q: 10. Have the background open and mounted for about a month now. Not only are wrinkles still present but there are pockets here and there and they do show on video. Steaming from what I read here takes care of the wrinkles. What fix does the manufacturer suggest to get rid of the pockets? Is there for example a technique for pulling the fabric around the rim? Can someone please describe the steps to take? Thanks.

A: Aside from steaming the wrinkles out, it is best to make sure that the wire frame within the background is not kinked in any way, which could be the cause of the pockets you're referring to. If using the white side, you can always light the background completely, which will essentially hide any imperfections on it.