The Impact Micro Clamp Double-Ended Spigot Kitfrom Impact Micro Clamp Double-Ended Spigot Kitis a handy accessory that can be used in a myriad of ways around the studio or on location. Lightweight and sturdy, it can clamp onto tubes with a maximum diameter of 1.38" (35 mm) and has a load capacity of 2.2 lbs (1.0kg). It features a 5/8" (16 mm) socket at its base. Optional accessories include Impact's CA100 Double Ended Spigot with 1/4"-20 and many other adapters and spigots.

1x Micro Clamp    1x Double-Ended Spigot    Clamp Load Capacity: 2.2 lb    Clamp Max. Diameter: 1.38"    5/8" Spigot, 1/4"-20 and 3/8"-16 Threads

Related Questions and Answers

Q: 1. What is the depth of the two M5 threaded holes? (So I can purchase the right M5 bolt length) Thanks in advance.

A: The M5 threaded holes are 15mm deep.

Q: 2. I Have Impact VC 500wln lights will this stand work with this light?

A: Yes any monolight than has a 5/8" receiver like the Impact VC-500WLN can work with this stand.

Q: 3. Is this good for elinchrom mono light?

A: This stand would be fine for holding an Elinchrom monolight lower to the ground.

Q: 4. Will this attach a be free fluid head to a magic arm mount?

A: Yes the Manfrotto 3/8" + 3/8" Adapter Spigot can attach to the BeFree head and the Magic Arm.

Q: 5. Can I attach this to a monopod, then attach the Wimberley Sidekick to this clamp?

A: You should be able to do that using this clamp.

Q: 6. Hi Can I attach a gimbal head to the clamp?,I want to clamp it to a shelf in a hide with gimbal head attached to mount my camera and large prime lens to.I believe the clamp can hold 30lbs is that correct?

A: You could attach a gimbal head to this clamp since it can hold up to 33 lbs. To get the head attached, you can use the Manfrotto 208HEX Head Mounting Plate with Hex Stud - 3/8 Thread B&H # MA208HEX which has a 3/8 male thread. Please see the image below for reference.

Q: 7. Is this the item I need to attach a light fixture to my new C stand?

A: Hi Paul - you need to have a grip head on the end of the arm, to which this piece can attach. I have put lighter weight lights (like Lowel I-Lights directly clamped on the end of the arm. So if your c-stand has an arm, clamp directly or use the grip head and this piece on the arm.

Q: 8. Is there a 1/4-20 hole on one end so that it can screw onto a 1/4-20 stud?

A: No, the Impact SRP-113 Long Double Stud 5/8" does not have a 1/4 20 hole. However. The aluminum Impact 5/8" Stud with 1/4"-20 Female Threads does. https://www.bhphotovideo.com/c/product/1334345-REG/impact_srp_112p_5_8_stud_with_1_4_20.html?sts=pi

Q: 9. Will this fit onto a guitar ?

A: It would depend on how wide the neck of your guitar was, I tried it on a Takamine acoustic around the neck, it may interfere with the strings on the fret board, alternatively it will fit up where the string clamps and tuning thumb screws are. Hope that helps.

Q: 10. will this spigot fit into my PhotoFlex LS-B2320Y stand?

A: Sorry, I don't know. I use it in knuckles (aka gobo heads). They fit those perfectly, and let you use an 3/8 or 1/20-20 threaded attachments.