Operating on the 5 GHz frequency band, the Ubiquiti airFiber AF-5-US 5GHz Gigabit Radio Bridgefrom Ubiquiti airFiber AF-5-US 5GHz Gigabit Radio Bridgeoffers point to point connectivity at long distances of over 62 miles. This enhanced coverage provides a reliable backhaul connection which is an essential part of many building-to-building enterprise network configurations. With a dual-antenna architecture, 2x2 MIMO functionality separates the transmit and receive data streams allowing for increased bandwidth and a more reliable connection. Setup of this PtP Gigabit radio is simple thanks to the airFiber Configuration Interface which can be installed by a single network tech. Once installed, 12 dedicated LED indicators make it easy to see the status of various aspects of the network including data port link/activity, data port speed, management port link/activity, and much more.

5 GHz Mid-Band Frequency Coverage    Over 1.2 Gb/s Throughput    Over 62-Mile Range    1 x Gigabit Ethernet PoE Port    40W Max Power Consumption    Includes PoE Adapter    Pole Mount Kit Included    Up to 125 mph Wind Survivability

• Point-to-point wireless platform
• Housed in a compact, highly efficient form factor
• Delivers wireless gigabit+ performance with low latency
• xRT feature uses an adaptive multi-channel coding scheme to enhance radio transceiver performance, while still maintaining regulatory compliance
• Supports long range communication up to 62+ miles
• Operates in license-free, mid-band 5 GHz frequencies
• Worldwide license-free operation
• Delivers gigabit performance at 1.0+ Gb/s
• Suitable for carrier backhaul, building-to-building enterprise use, or public safety applications

• Transmits data synchronously without any wait time
• Uses traditional TDD and FDD modes of operation
• Features the proprietary Hybrid Division Duplexing (HDD) mode for long range and spectral efficiency performance
• HDD technology calculates the propagation delay for synchronous transmissions and eliminate packet transmission latency
• Based on the ranging algorithm built into the air protocol

• Features a dual-independent, 2x2 MIMO, high-gain reflector antenna system
• Separate transmit and receive antennas eliminates the extra RF losses caused by the switches or duplexers
• Includes a mechanical back-plane that is constructed as a one-piece monocoque molding
• Single-piece, injection-molded architecture

• Network management option between the greater security of out-of-band management and the convenience of in-band management
• Full SNMP support for network management
• Local and remote status information available on the main tab of the airFiber configuration interface

• Proprietary INVICTUS core communications processing engine
• Features 1 MHz center channel resolution with Power Envelope Tracking technology
• Accurately and continuously controls transmit power relative to the band edge
• Power level automatically tracks to optimize performance near band edges, allowing you to choose the part of the band with the least interference

• Radio Alignment Display (RAD) makes aiming quicker and easier
• Dual, calibrated signal strength indicators display the actual signal strength on the local and remote airFiber radios in real time
• Displays information about GPS synchronization status, master/slave mode, RF link status, RF overload warning, current modulation mode, and link activity and speed for wired management and data ports

• Based on Ubiquiti's airOS
• Enables quick deployment
• Sliding-clamp design allows mounting hardware to be preassembled prior to installation
• Drop-in cradle mount design allows the installer to attach mounting hardware to the pole without having to support the weight of the airFiber radio during installation

Related Questions and Answers

Q: 1. Is this a USB-C or standard USB connection?

A: The Ubiquiti Networks Instant 802.3af to USB Adapter BH #UBINS3AFUSB uses a USB Type-A port.

Q: 2. None of the photos show a connection to AC power. Is there a standard three-prong recepticle plug on each end? (transmitter/receiver).

A: This type of antenna is best powered via PoE.

Q: 3. This device works for me when connected to a POE switch, but does NOT work when connected to a stand-alone Ubiquiti POE injector. Is there a way to make it work with the injector?

A: The Ubiquiti Networks Instant 802.3af to USB Adapter supports the Max. Power Input / Output 48V, 0.26A 5V, 2A Check the specs of the PoE injector.

Q: 4. Is this rated to be outside?

A: No, this is not a outdoor model. BH #UBUAPACMUS is rated to be outside

Q: 5. Is this HD unit compatible with a M/N: AF-5X radio?

A: It is not compatible.

Q: 6. Do I need 2 of these to make them work properly? or just with one sending the signal and another one cheaper receiving it?

A: Yes, 2 are required.

Q: 7. Does the US version of this kit support 220V AC?

A: Yes, the TP-Link TL-PA7017P supports 220 VAC.

Q: 8. Is this rated for in-wall use?

A: The manufacturer does not specify if the Ubiquiti Networks Instant 802.3af to USB Adapter is rated for in-wall use.

Q: 9. Can this AP be powered by a non-Ubiquiti PoE router such as Netgear GS108PE or TP Link SG1008PE?

A: It comes with a PoE injector, but it can be powered by PoE compatible routers as well.

Q: 10. Js this worldwide version?

A: This is USA version.