The Pelco EC-3016ULPOE-R EthernetConnect Local Cat5/Cat5e/Cat6 16-Port True PoE to 30W Rack-Mount UTP Extender is a 1 RU extender device useful beyond the 328' limit of traditional Ethernet. In addition, for system configurations that have a single cable connected to the camera, the extender can become a true PoE device and source PoE to the powered device. This eliminates the need for midspans or PoE-enabled Ethernet switches to provide a fully 802.3at compatible application. The extender provides maximum flexibility in these applications without any programming. The device is used to extend Ethernet over copper (EoC).

The unit extends sixteen channels of 10/100 Mb/s Ethernet with PoE+ power injection and pass-through PoE+ over twisted pair cable (Cat5/Cat5e/6 UTP). With the ability to connect directly to a PoE+ switch or the ability to generate PoE+ power with a 48 V input to the local end, the unit provides flexibility for extending a powered device (PD) over long distance copper.

Transmits individual Ethernet data channels with Power over Ethernet Plus (PoE+) power injection and pass-through PoE+ over standard Cat5/Cat5e/Cat6 UTP cable

Extends Ethernet up to 3000' at 10 Mb/s or 2000' at 100 Mb/s over Cat5/Cat5e/Cat6 UTP Cable

Extended temperature operation from -40 to 167°F (-40 to 75°C)

Extended pass-through PoE meets the IEEE802.3at standard for Power over Ethernet

Full 10/100 Mb/s bandwidth

Supports multicast, unicast, and jumbo frame

Symmetric bandwidth provides consistent upload and download with virtually zero packet loss over the total usable distance

Type tested to RFC-2544 TCP/IP network bandwidth packet transmission standards

User-selectable data rate for maximum bandwidth and transmission distance utilization

Complies with all major IEEE standards and RFC network protocols for UDP, TCP/IP, HTTP/HTTPs

Tested and certified by an independent laboratory for full compliance with the environmental requirements (Ambient Operating Temperature, Mechanical Shock, Vibration, Humidity with Condensation, High-Line/Low-Line Voltage Conditions, and Transient Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans Specification for Traffic Signal Control Equipment)

LED status indicators confirm operating status

Designed and manufactured in the USA

Related Questions and Answers

Q: 1. Does this come with the plastic bracket which the rubber eyecup uses to attach to the camera body?

A: Yes, FUJIFILM EC-XT S Small Eyecup for Select FUJIFILM Cameras has the plastic bracket built in.

Q: 2. Can the image be inverted on the display? I need to install one the folds up and one that folds down so that the two displays are one on top of the other

A: I am sorry but you will not be able to flip the image on the TLM-170GM. Feel free to email us directly at provideo@bhphoto.com if you'd like some help locating products that may work for your situation.

Q: 3. Will it work on the XH-1?

A: Yes they are compatible.

Q: 4. Will this fit the GFX 100s?

A: The FUJIFILM EC-XT S Small Eyecup for GFX 50S, X-T2, and X-T1 is also compatible with the FUJIFILM GFX 100S camera.

Q: 5. what are the base plate dimensions?

A: The base plate on the ER-148 is 20 x 20

Q: 6. What is the diameter of the circular opening?

A: The diameter of the circular opening is 23mm.

Q: 7. Will this hold Network Equipment as well? For example Mellanox routers? Are any rails needed?

A: This will hold anything that can be mounted in a 19 inch rack with nothing additional needed

Q: 8. What is the minimum and maximum rail-to-rail depths?

A: This has a minimum mounting depth requirement of 17 3/4″ and a maximum depth of 19 1/2″.

Q: 9. Will it fit an XT3?

A: Yes it fits Fuji X-T3

Q: 10. Will this fit a SKB Shallow Rack Case with a Rail-To-Rail Depth of 10.7?

A: It may work, but it is going to be very tight. You might have better luck with B&H # GAGR4S from Gator Cases which is shallow but has 14.25 Rack Depth.https://bhpho.to/2KB4cGv