The Acebil CS-280M Professional Tripodfeatures a 75mm CH2 Fluid Head, T750 Aluminum Tripod, MS-3 Mid-Level Spreader, RF-3 Rubber Feet, and a S-50 Carry Case. The head supports loads up to 13.2 pounds and has a 6-step counterbalance and indepedent 4-step pan and tilt drag. It comes equipped with a sliding quick-release plate and pan handle.

The 1-stage T750 tripod features a 75mm bowl and can be adjusted to provide a height ranging from 26.4 to 56.7". Enhanced tripod stability is provided via the MS-3 Mid-Level Spreader that holds the legs in position. The RF-3 Rubber Feet help protect indoor surfaces from tripod feet abrasions. A carrying case is included for easy storage and transport of the tripod system.

Supports Loads Up to 13.2 lb    CH2 Fluid Head    1-Stage T750 Aluminum Tripod    75mm Ball/Bowl    6-Step Counterbalance    4-Step Pan & Tilt Drag    Height Range: 26.4 to 56.7"    MS-3 Mid-Level Spreader    RF-3 Rubber Feet    S-50 Carry Case

• Supports up to 13.2 lb
• 75mm CH2 Fluid Head
• 6-Step counterbalance
• 4-Step pan/tilt drag
• 1-Stage T750 aluminum tripod with 75mm bowl
• Tripod height range: 26.4 to 56.7"
• MS-3 Mid-Level Spreader enhances tripod stability and holds the tripod legs in position
• MS-3 Mid-Level Spreader
• S-50 Carry Case included for storing and transporting the tripod system

Related Questions and Answers

Q: 1. what is the minimum working height?

A: They do not list the minimum working height, but the center column can turn 90 degrees and the legs can open to a very wide angle so you can get very close to the ground. I would say around 4-5 inches from the ground.

Q: 2. Will it work with this tripod FEISOL CT-3441T ?

A: One would need to attach Feisol short spikes to make the tripod usable with the dolly: https://bhpho.to/2FQufIF

Q: 3. Is the min height 17" or 25"? The aluminum version states both yet the Carbon somehow states its 17"

A: This tripod, Acebil T1002CM, has a height adjustment between 17.7 to 60.2''. The Aluminum Version, B&H # ACT1002G, is also 17.7 to 60.2". The model with a Height Range of 26.4 to 56.7" is a different tripod, it is the single stage B&H # ACT1000G.

Q: 4. Does the Acebil MP-285C monopod have a rubber foot or steel spike?

A: The Acebil MP-285C has a rubber foot.

Q: 5. What is the height of this tripod?

A: The tripod has a max height of 59 inches tall.

Q: 6. What type of feet are on this tripod?

A: The Acebil TAE-324F Aluminum Tripod features rubber feet.

Q: 7. is there another spreader I could use with this tripod to go lower, other than the one included?

A: There is a floor spreader model as well as this mid-level one seen here. Acebil T1002G Tripod Legs (100mm Bowl) B&H # ACT1002G. However, to get as low as possible with this tripod, you would have to remove whatever spreader it has. The lowest possible set up would come with a smaller tripod or a hi-hat. E-Image Hi-Hat with 75/100mm Bowl B&H # EI7500 is one possibility.

Q: 8. Min height is 25" or 17"? It says both. Then again for some reason the Carbon version says its 17" too.

A: The height range of this tripod is 25.2 to 58.3 inches.

Q: 9. I wanted to know if the model Acebil D3 and D5, are they compatible with the tripod Manfrotto 546b?

A: This particular combination is unknown so we cannot say for sure. However, the feet seem similar enough that the rubber tie-downs look like they would do the intended job. However, I would like to suggest that if you need something for the Manfrotto 546b, get the Manfortto 114MV Cine/Video Dolly. It is slightly more affordable and we know that will work.

Q: 10. Does it accept Arca style Q/R plates?

A: Yes, it does. :) It uses an arca-swiss style QR clamp.