You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.
Phones: 800
$ USD
  • Your shopping cart is empty!

Da-lite 24712fls Tensioned Advantage Electrol Motorized Screen

Da-lite 24712fls Tensioned Advantage Electrol Motorized Screen
  • Product Code: eq176680
  • Availability: In Stock

$13,764.00 $18,443.76

Designed to eliminate the extra step of finishing the screen with trim, the 120V Da-Lite 24712FLS Tensioned Advantage Electrol Motorized Screenfrom Da-Lite 24712FLS Tensioned Advantage Electrol Motorized Screenis designed with ceiling trim already in place. Once the screen is installed, the screen's trim conceals the rough opening eliminating the need to complete additional trim work. Sliding installation brackets are included to make it easy to attach the screen housing to the structure above the drop ceiling.

The Advantage Electrol screen features simple in-ceiling installation that can be done in two stages. The screen case can be installed during the rough-in construction stage and the fabric assembly can be completed during the finishing stage.

Da-Lite 24712FLS Tensioned Advantage Electrol Motorized ScreenThis screen does not include a box, and is designed for installations where a box has previously been selected. Please ensure the box you are using is compatible - i.e., is of the same size and has the same option - as with this fabric, roller, and motor assembly. The box that goes with this model number is: 24712BLS.

109" Diagonal / 16:10 Aspect Ratio    HD Progressive 1.3 Screen Surface    1.3 Gain / 150° Viewing Angle    Slim-Tab Tensioning System    White Powder-Coated Case    Installs Above the Ceiling    Black Backing Standard    Fabric, Roller, Motor Only    Silent Motor    Low Voltage Control (LVC)

Key Specs
Front/Rear ProjectionFront
MotorQuiet
Viewing Area57.5 x 92.0 (109)" / 146.1 x 233.7 (276.9) cm
Aspect Ratio16:10
Gain1.3
TensionedYes
Type
Front/Rear ProjectionFront
StyleCeiling-Recessed, Wall and Ceiling
MotorQuiet
Surface
Viewing Area57.5 x 92.0 (109)" / 146.1 x 233.7 (276.9) cm
Aspect Ratio16:10
Finish NameHD Progressive 1.3
Gain1.3
Viewing Angle150 degrees
TensionedYes
General
Height AdjustableYes
Low Voltage ControlYes
Voltage120 VAC/60 Hz

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

  • Smooth Roll Technology to keep your screen flat
  • Slim-Tab, a lower profile and stronger tab design to keep your screen taut
  • Tensioning Cable System to prevent warping and ensure even lateral tension

  • UL Plenum rated case
  • White powder-coated case for a clean aesthetic
  • Black-backed screen material for enhanced image quality and opacity
  • Seamless surface

This screen comes with the screen fabric, roller, and motor only, meaning the box must be purchased separately. This design allows the box to be installed during the construction phase while the screen can be installed later, once construction is complete. This ensures the screen won't be damaged during construction

Designed to provide silent operation when raising or lowering the screen

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely

Related Questions and Answers

Q: 1. Will this work with the iphone SE2 and the Insta360 1 R action camera?

A: Yes, there should be no issues with either of those devices.

Q: 2. Is the joystick variable?

A: The Vidpro Motorized Pan & Tilt Gimbal Head joystick speed is variable.

Q: 3. What is a good case to store the Moza Mini-P?

A: The Moza Mini-P comes with an EPP Bag. There is no dedicated bag for the Moza Mini-P but sling bags seem to be a good option.

Q: 4. Does this work with the Iphone SE2 and the Insta360 1R camera?

A: Yes, this will work with both.

Q: 5. Will this work with the Go Pro Hero 10?

A: Although there is no control listed with the GoPro Hero 10, a GoPro Hero 10 can be mounted to the camera carriage of the Moza Mini P gimbal with a tripod adapter. Example is Revo Tripod Adapter with 1/4"-20 for GoPro B&H # RETPMGP MFR # AC-TM. https://bhpho.to/3mTWMyF

Q: 6. Is this gimbal compatible with the Canon PowerShot SX60 HS or the Canon PowerShot SX70 HS?

A: Yes this will work with the canon power-shot cameras

Q: 7. Can it work with Canon Camcorders like the vixia HF R80/R800? Also Canon EOS T6?

A: There should be no issues using the stated cameras on this gimbal.

Q: 8. Can this be mounted upside down on a jib?

A: We have attempted to contact Vidpro regarding your question and have not received word yet. it is our opinion that it should work upside down since remote heads often are needed to work in such a configuration. We will post as soon as we receive a response.

Q: 9. Is this a true gimbal. If I mount this at the top of a pole will it stay level if the pole base is not?

A: The mount or pole needs to be plumb and level in order for this device to work properly.

Q: 10. Are you able to choose rotation angle? i.e. press button to turn 10 degrees?

A: Not that we are aware of. This product offers the ability to change the rotation speed, but we are not aware of it allowing you to precisely dial in an angle to go to. You would have to do that manually.

06/09/2024

[Yes] I love this product, Easy to install and and look even better on the wall.

5
26/08/2024

[120 VAC/60 Hz] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projector up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem!

5
06/08/2024

[1.3] I installed in my living room in between ceiling joists. It works great. I use it with a Panasonic HD projector. It impresses everyone who walks in the room. Has a clean appearance when retracted. Note: it didn't come with a 12v trigger as both the B&H customer service rep and myself thought it did. We both misunderstood the description (it's optional.) The part was available at Da-Lite for $80 and came with no instructions. I got it to work after a few emails and chats with da-lite. Also, I ended up placing some holes in the top of the case to mount using 8 Lag bolts into the 2nd story floor structure. All the hardware that comes with it assumes you will have access to hang it from the top which requires access via the side while it's in it's final position. I was putting it in a hole the size of the case in my finished ceiling so that method would not work ( I would have had to remove and re-install a lot of drywall). I knew this before I purchased by reading the installation instructions so no worries just a fact and maybe a consideration for future changes to the case or just the directions.

5
29/07/2024

[1.3] This screen was installed in a small conference room with an NEC projector. The screen can be wall or ceiling mounted, and this flexibility came in handy when we had to switch to a ceiling mount at the last moment. The screen presents very well, and is unobtrusive when retracted. The tensioning system works nicely, and we didn't have to change any of the factory settings for the drop. I would have liked to see some additional mounting holes for attaching the screen to studs in the wall, so the installer has more options for wall mounting.

5
13/06/2024

[Yes] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projection screen/case up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem!

5
11/06/2024

[16:10] I used this screen in a small conference room and it was very simple to instal.

5
06/06/2024

[Yes] We use the screen in our church sanctuary once or twice a month. Installing it was an adventure with the weight and length, but several sections of scaffolding and a couple friends made the install move along nicely. The instructions for wiring were right on and it worked first try! The image is right on and visible the entire length of our viewing area (over 100').

5
29/05/2024

[Front] This Screen was easy to install. It took 3 people and 2 ladders to get the job done. The remote is really not needed but i opted to install it as well. The motor runs really smooth. The screen is nice and wide. A really good buy.

5
25/05/2024

[Yes] Looking forward to getting all of this stuff together

5
09/05/2024

[Yes] Assembly for very straight forward. Looks great on the wall. Really like the velour wrap around the frame. It does a very good job of rejecting light back onto the screen. Because of the size, (110 inch) I decided to put up a folding screen to cover it when not in use.

5

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

Top Bestselling Products

Da-lite Tensioned Advantage Deluxe Electrol Screen

$21,208.80 $26,935.18

Da-lite Tensioned Large Advantage Electrol Screen

$50,505.00 $67,171.65

Products You May Like

Cinemilled Ronin Arm Extensions Pair

$599.97 $731.96

Foldio3 25" Mini Studio With Halo Bar

$513.00 $713.07

Zacuto Act Recoil Rig Panasonic Gh6

$2,997.00 $3,866.13

Axis T90d25 White Led Illuminator Ac/dc Power

$1,437.00 $1,968.69

Soundtube Rs600i 6.5" Coaxial Ceiling Speaker

$1,200.00 $1,476.00