The FL-540P floor box is designed for raised access carpeted floors. This floor box provides a practical solution for cable storage while maintaining easy access. The lift off section of the cover allows full access to the internal cables and connector plates. A smaller hinged trap door folds back to create the cable exit. Cables can be stored within the box when not in use, allowing unencumbered travel over the floor. The sturdy drop-in floor lip supports the unit and installs flush with the floor.
The innovation continues to the configurable back box. The FL-540P's internal brackets can be arranged to provide numerous options for both high and low voltage standard gang openings making it the most flexible and easiest to install floor box available.

• 11-gauge steel temporary construction cover included
• 11-gauge finished steel cover with choice of carpet edging
• Mitered brass or aluminum carpet edging .5" or .25" high
• Stainless steel compression latches
• Lift-off full access door

Related Questions and Answers

Q: 1. What is the approx weight of the mattebox without top flag and 15mm rod adapter?

A: We cannot examine the item itself but would guesstimate 2.5 to 3lbs.

Q: 2. I'm looking for a matte box to use on a Sony 200-600mm lens. Will this matte box work? I want to run a VND. Thanks!

A: Yes, the Tilta 3-Stage 4 x 5.65" Carbon Fiber Clip-On Matte Box (110mm Back) could work if you have 15mm rod mounts. However, you may want to consider the Tilta Mirage VND Matte-Box that would screw into the filter threads of your lens model. The Mirage comes with ring sizes up to 82mm. Tilta Mirage VND Kit BH #TIMBT16A

Q: 3. Will this work with the Tilta MB-T12 Matte Box?

A: Yes. The following unit will accommodate matte box lens opening ranging from 134/114/110/95/80mm.

Q: 4. Do you just sell replacement parts? Say for instance I need just the 80mm adapter ring/backing

A: We do not have replacement parts for this matte box and generally speaking manufacturer's prefer to sell the replacement parts. Please contact Tilta at a href= http://tilta.com target= _blank tilta.com/a or ikan, Tilta's USA distributor at a href= http://ikancorp.com target= _blank ikancorp.com./a

Q: 5. Does this come with step down rings?

A: The Tilta MB-T12 does not come with step-down rings.

Q: 6. Is it possible to use donuts with this matte box?

A: I don't see why not. You would have to source the rubber and custom cut them but other than that it should work if the lenses barrels are flat enough and their is no in/out extension while focusing.

Q: 7. Would the SmallRig Clamp-On Ring Kit work with this Matte Box? The SmallRig ClampOn Rings are 9mm in Width. How Width is the Backing?

A: They should work, as the opening on the mattebox is 114mm, just like the largest ring in the kit.

Q: 8. Will this Fit into Tilta MB-T04 Mattebox (4x5.65 Swing Away Studio Mattebox)? https://www.bhphotovideo.com/c/product/992629-REG/ikan_mb_t04_4x5_65_carbon_fiber_matte.html

A: No it will NOT

Q: 9. What are the thickness of the tray holders? Would it fit the Tiffen Multi Rota Tray Variable Neutral Density Kit? Thanks.

A: Tiffen has a compatibility chart up on their website for their Multi Rota Tray Products. This Matte Box is not listed on that page, it has yet to be tested with the Matte Box and it may not work properly.http://bit.ly/2eQHAgrWe do have some options that are listed on Tiffen's Compatibility from Bright Tangerine, Chrosziel and Vocas that you could look in to instead. They are B&H Numbers BRB12300012, CH41502F11 and VOMB455S.

Q: 10. I'm looking for something that fits the sony PZ 28-135mm. Would this fit the 105mm diameter with an adapter?

A: No, the Tilta 3-Stage 4 x 5.65” Carbon Fiber Clip-On Matte Box will not be able to attach to the Sony PZ 28-135 mm. You would need to measure the front of the lens with a caliper to get the diameter of the end of the lens. Another option would be to work with the included 15 mm rod mount and a 15 mm baseplate that allows you to work with 15 mm rods. It could be mounted that way.