The Acebil CS-282G Professional Tripod System for Camerasfeatures a 75mm ball CH2 Fluid Head, T752 Aluminum Tripod, GS-3 Ground Spreader, and a S-52 Carry Case. The head supports loads up to 13.2 pounds and has a 6-step counterbalance and independent 4-step pan and tilt drag. It comes equipped with a sliding quick-release plate and pan handle.

The 75mm bowl T752 tripod features a 2-stage design and aluminum construction. It has a height range of 17.7 to 60.2" and comes with a GS-3 Ground Spreader for enhanced stability. A carrying case is included for easy storage and transport of the tripod system.

Supports Loads Up to 13.2 lb    CH2 Fluid Head    2-Stage T752 Aluminum Tripod    75mm Ball/Bowl    6-Step Counterbalance    4-Step Pan & Tilt Drag    Height Range: 17.7 to 60.2"    GS-3 Ground Spreader    S-52 Carry Case

• Supports up to 13.2 lb
• CH2 Fluid Head (75mm ball)
• 6-step counterbalance
• 4-step pan/tilt drag
• 2-stage T752 aluminum tripod with 75mm bowl
• Tripod height range: 26.4 to 56.7"
• GS-3 Ground Spreader enhances tripod stability and holds the tripod legs in position
• S-52 Carry Case included for storing and transporting the tripod system

Related Questions and Answers

Q: 1. What type of feet are on this tripod?

A: The Acebil TAE-324F Aluminum Tripod features rubber feet.

Q: 2. Can this dolly be used on a tripod without spiked feet?

A: The Acebil D3 is only compatible with spiked feet tripods.

Q: 3. is there another spreader I could use with this tripod to go lower, other than the one included?

A: There is a floor spreader model as well as this mid-level one seen here. Acebil T1002G Tripod Legs (100mm Bowl) B&H # ACT1002G. However, to get as low as possible with this tripod, you would have to remove whatever spreader it has. The lowest possible set up would come with a smaller tripod or a hi-hat. E-Image Hi-Hat with 75/100mm Bowl B&H # EI7500 is one possibility.

Q: 4. I wanted to know if the model Acebil D3 and D5, are they compatible with the tripod Manfrotto 546b?

A: This particular combination is unknown so we cannot say for sure. However, the feet seem similar enough that the rubber tie-downs look like they would do the intended job. However, I would like to suggest that if you need something for the Manfrotto 546b, get the Manfortto 114MV Cine/Video Dolly. It is slightly more affordable and we know that will work.

Q: 5. Can I use this dolly with sachtler flowtech 75 spike foot?

A: Yes, you will be able to use the Sachtler Flowtech 75 Spike Foot tripod with this dolly.

Q: 6. Can I use this with the iFootage Wild Bull T5S with the spiked feet (rubber feet removed)?

A: Yes, the Acebil D3 Dolly for Professional Tripods is compatible with the iFootage Wild Bull T Series T5S Aluminum Alloy Tripod.

Q: 7. what is the minimum working height?

A: They do not list the minimum working height, but the center column can turn 90 degrees and the legs can open to a very wide angle so you can get very close to the ground. I would say around 4-5 inches from the ground.

Q: 8. Will this work with Miller Sprinter II Tripod?

A: The Acebil D3 Dolly should work. However, we can only recommend that you choose the Miller Dolly made for the Sprinter II tripod. Miller 391 Lightweight Dolly - for DS Tripods BH #MI391

Q: 9. Will the Slik SBH-550 ball head screw onto this tripod?

A: Yes, the SBH550 will mount to the Professional legs (once you remove the threaded insert).

Q: 10. Will it work with this tripod FEISOL CT-3441T ?

A: One would need to attach Feisol short spikes to make the tripod usable with the dolly: https://bhpho.to/2FQufIF