The Acebil CS-480G Professional Tripod System for Photographyfeatures a 100mm ball CH4 Fluid Head, T1000 Aluminum Tripod, GS-3 Ground Spreader, and a S-50 Carry Case. The head supports loads up to 26.4 pounds and has a 6-step counterbalance and independent 4-step pan and tilt drag. It comes equipped with a sliding quick-release plate and pan handle.

The 100mm bowl T1000 tripod features a 1-stage design and aluminum construction. It has a height range of 32.2 to 53.3" and comes with a GS-3 Ground Spreader for enhanced stability. A carrying case is included for easy storage and transport of the tripod system.

Supports Loads Up to 26.4 lb    CH4 Fluid Head    1-Stage T1000 Aluminum Tripod    100mm Ball/Bowl    6-Step Counterbalance    4-Step Pan & Tilt Drag    Height Range: 32.2 to 53.3"    GS-3 Ground Spreader    S-50 Carry Case

• Supports up to 26.4 lb
• CH4 Fluid Head (100mm ball)
• 6-Step counterbalance
• 4-Step pan/tilt drag
• 1-Stage T1000 aluminum tripod with 100mm bowl
• Tripod height range: 32.2 to 53.3"
• GS-3 Ground Spreader enhances tripod stability and holds the tripod legs in position
• S-50 Carry Case included for storing and transporting the tripod system

Related Questions and Answers

Q: 1. Can I use this with the iFootage Wild Bull T5S with the spiked feet (rubber feet removed)?

A: Yes, the Acebil D3 Dolly for Professional Tripods is compatible with the iFootage Wild Bull T Series T5S Aluminum Alloy Tripod.

Q: 2. Min height is 25" or 17"? It says both. Then again for some reason the Carbon version says its 17" too.

A: The height range of this tripod is 25.2 to 58.3 inches.

Q: 3. What is the size of the half-ball do I need to purchased for this type of tripod?

A: This is a 100mm bowl tripod. You would need to purchase a half ball like the Benro 100HB 100mm Half Ball Adapter, BH #BEBL100. https://bhpho.to/2kVsdwi

Q: 4. Is this head compatible with manfrotto 501 quick-release plates?

A: Unfortunately, the Acebil I-605DX is not compatible with the Manfrotto 501pl plate.

Q: 5. what is the minimum working height?

A: They do not list the minimum working height, but the center column can turn 90 degrees and the legs can open to a very wide angle so you can get very close to the ground. I would say around 4-5 inches from the ground.

Q: 6. Can you plug this in and use it while it's charging?

A: Yes, this can be plugged in.

Q: 7. is there another spreader I could use with this tripod to go lower, other than the one included?

A: There is a floor spreader model as well as this mid-level one seen here. Acebil T1002G Tripod Legs (100mm Bowl) B&H # ACT1002G. However, to get as low as possible with this tripod, you would have to remove whatever spreader it has. The lowest possible set up would come with a smaller tripod or a hi-hat. E-Image Hi-Hat with 75/100mm Bowl B&H # EI7500 is one possibility.

Q: 8. What type of feet are on this tripod?

A: The Acebil TAE-324F Aluminum Tripod features rubber feet.

Q: 9. What is the height of this tripod?

A: The tripod has a max height of 59 inches tall.

Q: 10. I wanted to know if the model Acebil D3 and D5, are they compatible with the tripod Manfrotto 546b?

A: This particular combination is unknown so we cannot say for sure. However, the feet seem similar enough that the rubber tie-downs look like they would do the intended job. However, I would like to suggest that if you need something for the Manfrotto 546b, get the Manfortto 114MV Cine/Video Dolly. It is slightly more affordable and we know that will work.