With the TRENDnet TK-214i 2-Port DVI USB KVM Switch with Audiofrom TRENDnet TK-214i 2-Port DVI USB KVM Switch with Audioyou can control two computers using a single keyboard, mouse, and monitor. This KVM switch comes equipped with two sets of combination cables each featuring DVI, USB, audio, and microphone ports. These connectors ensure you can utilize all aspects of your connected Windows, Mac, or Linux based PC. The console side of the KVM switch features one DVI port for a monitor, two USB ports for your mouse and keyboard, one 3.5mm audio port, and one 3.5mm microphone port. On the console itself you will find a push button switch making it easy to flip back and forth between connected PCs.

Supports 2 Computers    DVI-I Connectors    USB Connectors    3.5mm Audio Ports    3.5mm Microphone Ports    Supports Resolutions up to 1920 x 1200    Bus-Powered    Hot Plug Support    Plug-and-Play Compatible

1 x DVI port

2 x USB 2.0 Type A port

1 x 3.5 mm audio port

1 x 3.5 mm microphone port

LED display for easy computer monitoring

Push button switch with a 4.8 ft / 1.45 m extension cable

2 sets of 2.6 ft / 80 cm built-in combination cables with DVI, USB, audio, and microphone ports

Related Questions and Answers

Q: 1. I need to assign specific devices on my LAN to use specific WAN. Can i do this w a routing table?

A: You can use routing tables with the TRENDnet TEW-829DRU AC3000 Wireless Tri-Band Gigabit Router BH #TRTEW829DRU.

Q: 2. How to factory reset the adapters?

A: Hi Erby! Thanks for your interest in TRENDnet! Press the reset button on the bottom for 1 second. Resets device to factory defaults settings (All LEDs will turn off and on again). Note: Will reset to the factory default private network name “HomePlug AV”. Hope this helps! If you have any more questions, you can always respond directly to this thread and someone will be happy to try and help answer any additional questions you may have! Have a great day! Adrian TRENDnet CS

Q: 3. Is this a low noise mic pre amp tube ?

A: Yes. The Telefunken ECC83-TK black diamond series preamp tube offers cleaner headroom than the typical 12AX7.

Q: 4. Will this work if I have an xlr extension cable running from the mic to the device itself? Or does it need to be plugged direct

A: Yes, the Polsen XLR-USB-48 XLR to USB Audio Interface does not need to be plugged into the microphone. You can use an XLR just like any other audio interface.

Q: 5. Is it two 3.5 female inputs and one 3.5 female output?

A: That's correct Tony, it's all female 3.5mm inputs on this unit.

Q: 6. How do you factory reset the adapters?

A: On the bottom of the device you should see a reset button, stick a small pin inside and hold down for 10-15 seconds. This should reset the device to factory settings

Q: 7. If a phantom button is pushed on, will it be memorized after the unit is turned off or disconnected?

A: As per MOTU, the unit would default to it's last settings prior to being powered down. The Phantom Power should remain on.

Q: 8. Would the tube work in a Rode NTK? And is this tube manufactured in Germany?

A: This twin- triode tube is made in the Slovak Republic, and is also known as the 6922, which can be used as replacement valve for the Rode NTK microphone.

Q: 9. is this interface work with Mac Catalina?

A: Yes, this interface is compatible with macOS Catalina.

Q: 10. Can one assign different devices on the LAN to specific WAN connections, eg via a routing table?

A: You can setup routing tables with the TRENDnet TEW-829DRU AC3000 Wireless Tri-Band Gigabit Router BH #TRTEW829DRU.