The DisplayPort to VGA Adapter from Prudent Way is equipped with one male DisplayPort input and one female VGA output, allowing you to connect any device with a DisplayPort output to any display with a VGA input. This adapter is compliant with DPCD (DisplayPort Configuration Data) Revision 1.1 and supports resolutions up to 1920 x 1200 at 60Hz.

DisplayPort Male Input    VGA Female Output    Nickel Plated    Full 1080p HD Video Support

Related Questions and Answers

Q: 1. Will this head be compatible with the Benro GC168T GoTravel Carbon Fiber Tripod?

A: I believe so, but I am not 100%. I bought a refurbished Gitzo Mountaineer tripod with this mount and the two work perfectly. Wish I read more about this mount as it is not the best for DSLR cameras, but great for binoculars.

Q: 2. How wide is the head from pan knob to handle lock knob?

A: 6 inches

Q: 3. Can I use it like an gimbal head ? Can I lock the horizon and just move up and down with circle move ?

A: It may be the closest head to a gimbal but you will achieve much results with a gimbal head as far as tracking and smoothness of motion.

Q: 4. If I wanted to point my camera straight up can this head accomplish that? Would I have to turn the camera a quick release plate around backwards?

A: I use a Manfrotto 410 geared head which has the same limited up pointing constraint. I mount my telescope, which obviously needs to point way up, on it. To get around the up pointing constraint I mount the QR plate with the telescope pointing "backwards." When I connect the telescope to the mount I am using the downward pitch as my upward pitch. Since the Benro plates are Arca-Swiss comparable there is no front or back to them. To maintain 3-way operation I would mount the plate in line with the optical axis of the camera and mount the camera to the head with the lens pointing out over the pitch handle. That is going to require reaching around the head to got to that handle which will be a little awkward, but allows control of pitch, yaw, and roll which becomes limited if the camera is mounted "sideways" as suggested by Staff.

Q: 5. Do I need a different plate for the Swarovski ATX 95mm?

A: No plate is needed. The ATX 95mm scope has a built in Arca foot so you will not even use the plate that comes with this Gitzo head (unless you want to use the head with a camera).

Q: 6. Would this be a suitable substitute for the Q2 ball head on a MeFoto C2350 tripod?

A: Yes, the Benro HD3A 3-Way Panhead will be a suitable substitute for the ballhead included with the MeFOTO GlobeTrotter Carbon Fiber Travel Tripod Kit if you are interested on setting specific angles while panning and tilting on your camera.

Q: 7. plus/minus 110 degrees? Is that 220 degrees of motion, or really just +55, -55 ( etc)??

A: i looked at mine last night -- horizontally 360 degrees and vertically 180 degrees (full range of motion not 1/2) -- not sure where the 110% comes from.Mike

Q: 8. Does that fit on the Traveler GT545T?

A: Yes it does. You will be able to put this head on a tripod like B&H # GIGT0545TUS. https://bhpho.to/2ti0hEM

Q: 9. Hello. Will this work with Gitzo GT2542 tripod, canon R6ii, RF 100-500 and 1.4 extender? Stills and video. Thank you.

A: Yes, the Gitzo 2-Way Fluid Head would work with the Gitzo GT2542 Mountaineer Series 2 Carbon Fiber Tripod for stills, or video. It would also support your payload weights.

Q: 10. will arca swiss plates work with this tripod?

A: I have PMG plates on my spotting scope and telephoto lenses and they perfectly fit this head.