The 500' Laird RG59 1855A Cable with Neutrik BNC Connectors 500'from Laird RG59 1855A Cable with Neutrik BNC Connectors 500'is built for extended bandwidth for 6G-2K video applications. Neutrik's rearTWIST BNC connectors offer increased headroom and additional return loss reserve for potential impedance deviations resulting from cable bending, incorrect connector assembly, or faulty connection interfaces without signal interruption. The rearTWIST technology simplifies insertion and removal of recessed BNC panel connectors and enables easy patch bay interfacing. No special BNC removal tool is required, simply use the rear boot twist.

Belden 23 AWG RG59 1855A Mini Coax Cable    2 x Neutrik rearTWIST UHD BNC Connectors    Supports up to 6G-SDI/2K Signals    75 Ohms, 500' Cable Length    For Recessed Panel-Mount BNC Connections    Easy rear-Twist Insertion/Removal

Belden RG59 1855A mini coaxial cable with a 23 AWG

Related Questions and Answers

Q: 1. Will this work with the pluto trigger and a Sony A1 camera?

A: The Vello 2.5mm Remote Shutter Release Cable II for Cameras with Sony Multi-Terminal Connectors will work for a camera with a Sony multi interface port such as the A1 and a trigger with the 2.5mm female port, yes.

Q: 2. This Vello cable comes in either a 3.5mm or 2.5mm configuration. I assume this is referring to the end of the cable that plugs into the receiver as the other end is 3-pin, and plugs into the camera. So is the mm choice determined by what size connection is on the Vello receiver?

A: Yes the 2.5mm or 3.5mm end is for the type of connection on the receiver.

Q: 3. what is the length from the end of the Canon 3-pin connector to where the cable begins to coil?

A: From the end of the 3-pin connection to the start of the coil, the length of cable measures approximately 4" / 10cm.

Q: 4. Do they make such a cable that doesn't have the right angle on the 10-pin side?

A: No, the Vello 2.5mm Remote Shutter Release Cable II for Cameras with Nikon 10-Pin Connectors only comes with a right-angle design.

Q: 5. Will this work with a Sony A7iii

A: Yes, the following cable is designed for the Sony multi-terminal cameras and will adapt to the following Sony units. Alpha: a1, a9 II, a9, a7S III, a7S II, a7S, a7R IV, a7R III, a7R II, a7R, a7 IV, a7 III, a7 II, a7, a6600, a6500, a6400, 6300, a6100, a6000, a5100, a5000, a3000, a99 II, a77 II, a68, a58 Cyber-shot: RX1R II, RX10 IV, RX10 III, RX10 II, RX10, RX100 VII, RX100 VI, DSC-RX100 VA, RX100 V, RX100 IV, RX100 III, RX100 II, HX50V, HX90V, HX400V, HX400, HX300, and ZV-1

Q: 6. Can it be used with lanc to control a7iv?

A: The Vello 2.5mm Remote Shutter Release Cable II for Sony Multi-Terminal Cameras cannot be used with lanc to control the a7 IV.

Q: 7. Will this work to connect a Godox V1 and a MiNT Flashbar 2?

A: The Vello 2.5mm Remote Shutter Release Cable II for Cameras with Canon Sub-Mini Connectors allow the user to connect a flash with the 2.5mm port to a camera. The Mint Camera Flash Bar 2 and the Godox V1 Flash can not be connected throughout a cable.

Q: 8. Both the c1-25 and the c1-35 list the Fuji XH2s as being compatible. How is this possible?

A: The Vello 2.5mm Remote Shutter Release Cable II for Cameras with Canon Sub-Mini Connectors is the appropriate cable. The Fujifilm X-H2S Mirrorless Camera uses a 2.5mm port for a remote connection. This is easily missed since the port is located on the right side of the camera, rather than the usual left side.

Q: 9. Will this work with fujifilm x s10?

A: Yes, the Vello 2.5mm Remote Shutter Release Cable II for Canon Sub-Mini Cameras is compatible on the Fujifilm X-s10.

Q: 10. Will this work with the Sony DSC-HX99?

A: Yes, this Vello 2.5mm Remote Shutter Release Cable II for Sony Multi-Terminal Cameras does work on the Sony DSC-HX99.