The black Sanken COS-11D Lavalier Mic with TA4F Connectoris a subminiature lav microphone designed to deliver clear, full-bodied sound and reliable performance, making it a popular choice among industry professionals in broadcast, TV, theater, film, videography, and more. 

Engineered to meet the standards of modern digital wireless microphone systems, the COS-11D is RF shielded to eliminate interference issues and ensure a pristine audio signal. The microphone capsule features a rectangular design that sits vertically, increasing the surface area and allowing this tiny mic to offer a rich, full sound that outperforms many larger models.

The mic's 50 Hz to 20 kHz frequency response rolls-off extreme low end and provides accurate, transparent audio reproduction with a small presence boost in the 6 kHz area for crisp, intelligible speech. With a forgiving omnidirectional polar pattern that picks up sound in a 360° pattern, levels stay consistent even when the subject turns away from the mic.

A water-resistant mesh screen protects against humidity, perspiration, makeup, bad weather, and other potential on-location issues, while the durable cable is also moisture-resistant and built to stay soft and pliable, even after extended use. This version of the COS-11D terminates in a TA4F connector and is wired for use with Trantec transmitters. A metal windscreen, holder clip, rubber mount, and plastic case are included.

For Broadcast, Film/Video & Presentation    Omnidirectional for Consistent Levels    For Trantec Transmitters with TA4M    -9 dB Reduced Sensitivity Level    Rugged 5.9' Cable Stays Pliable    RF Shielded for Digital Wireless    Water Resistant    Small Size Is Easy to Conceal    Requires 3 to 10 VDC    Includes Windscreen, Mount & Clip

• Trantec: Works with Trantec bodypack transmitters equipped with a TA4M connector including the S5.5 Series.
• Also works with third-party wireless transmitters that are equipped to supply 3 to 10 VDC through a TA4M connector wired for Trantec compatibility.

Related Questions and Answers

Q: 1. Will this work with the rode ntg2 and the canon c100 markII?

A: Yes, the Sanken rubber O-rings will work with the Canon C100 MKII to secure the Rode NTG2.

Q: 2. Will this work for connecting a Rode Lav mic to a Sony a6300?

A: This connector will allow the Rode Lavalier Microphone, BH #ROLAV to connectt with the Sony a6300 camera.

Q: 3. Is this the latest version with ground protection?

A: Yes it is. This is the latest version of the Lentequip SafeTap Connector and it features Ground Protection.

Q: 4. Is this mic compatible to be used with a Denecke PS power supply? I'm having a problem, cause I just hear a loud hum noise and no transmitter signal. I tried it with other mics and transmitters, and I hear the same loud hum noise.

A: Yes, the Sanken CS-M1 can be used with the Denecke PS-1A or PS-2 which are both compatible 48V phantom power supplies. The Denecke PS-T is not compatible for use with the CS-M1 because it is a 12V "T-power" supply intended for use with older microphones that require lower voltage and the CS-M1 requires 48V phantom power.

Q: 5. what is the max DC input voltage ?

A: 9V is the maximum.

Q: 6. How is this different from the v1 connector?

A: The V1 uses a red retainer that slides in place to secure the pin in place.

Q: 7. I'm very fond of Sanken mics personally. Thus I wanted to ask how is the reach on this mic. Is there anything you guys could tell in that regards? I know it's not a shotgun mic, however it's Super Card.

A: It very similar to most of other shotgun mics (and it's a shotgun mic). Not as directional as Sennheiser 416, so I wouldn't recommend if you need to capture sounds outdoors very far away.

Q: 8. What is the voltage? Center positive?

A: The voltage is 7.2. It is only compatible with the Sigma DP Quattro and and FP cameras cameras so far.

Q: 9. Can I simply attach this to a shoe mount on the FX3 and use it?

A: Yes. The CS-M1 will work with the FX3

Q: 10. What SafeTap Connector Rev. is this?

A: The Lentequip SafeTap Connector Rev 4 was released over 2 years ago and B&H stock is current.